manualshive.com logo in svg

HydraMaster Steamatic 8800 TMU, Руководство пользователя, Страница: 51 / 148

Поделиться
Скачать
HydraMaster Steamatic 8800 TMU Скачать руководство пользователя страница 51

5-9 - Machine Maintenance

Steamatic 8800 TMU

Servicing Valves on the High pressure pump

Removing a Valve

Remove the valve cap (30 mm) and extract the valve assembly (see 

1. 

figure 5-1).

Remove the valve assembly (retainer, spring, valve plate, valve seat) from the valve 

2. 

cavity.
Remove the o-ring and support from the valve cavity.

3. 

examine  the  o-ring  and  replace  if  there  is  any  evidence  of  cuts,  abrasion,  or 

4. 

distortion.
Inspect the manifold for wear or damage (see 

5. 

figure 5-2).

Inspect the old valves for wear or damage. only one valve kit (P/N 000-078-519) 

6. 

is necessary to repair all the valves in the pump. (The kit includes new supports, 
o-rings, valve seat, valve poppet, spring and retainer; all are pre-assembled.)

figure 5-1.  remove Valve Cap and Valve assembly

figure 5-2.  Inspect manifold and old Valves

Содержание Steamatic 8800 TMU





















































































































































Отзывы:

Нет отзывов