manualshive.com logo in svg

HydraMaster Steamatic 8800 TMU, Руководство пользователя, Страница: 62 / 148

Поделиться
Скачать
HydraMaster Steamatic 8800 TMU Скачать руководство пользователя страница 62

Machine Maintenance  

- 

5-20

 

Steamatic 8800 TMU

To freeze guard the hoses and wand, perform Step 6 in the preceding procedure 
with the items to be freeze guarded attached.

Always check the freezing level of your reclaimed antifreeze with a glycol tester 
before reusing. failure to do so may result in serious component damage.

recovering antifreeze for re-use

Attach all hoses and wands which have been freeze guarded to the truckmount.

1. 

Attach the incoming water source to the front of the truckmount.

2. 

Start the truckmount.

3. 

Spray the solution through the hoses and wands into a sealable container until all 

4. 

signs of antifreeze are gone. 

freeze protection of the pump-In System

Drain the fresh water tank.

1. 

Remove  the  garden  hose  adapter  from  the  pump-in  pump  hose  and  position  the 

2. 

hose so it is pointing outside the van.
Turn on the pump-in pump and run for 1 - 2 minutes until all the water is purged from 

3. 

the hose.

The next time the truckmount is used, it may take a few minutes before the water 

box begins to fill.

Содержание Steamatic 8800 TMU





















































































































































Отзывы:

Нет отзывов