HydraMaster Steamatic 8800 TMU Скачать руководство пользователя | Manualshive

Страница: 15 / 148

background image

1-7 - General Information

Steamatic 8800 TMU

Never smoke in or around the truckmount. Doing so will increase the risk of fire

and explosion. Serious injury or death may result.

During the operation of the truckmount the exhaust system will become extremely

hot. Keep all flammable materials away from the truckmount exhaust system.

Failure to do so will increase the risk of fire and explosion. Serious property

damage may result.

Never operate the truckmount when the vehicle is tilted more than 10 degrees in
any direction. Doing so will result in improper lubrication of the internal components,
and will increase the risk of serious component or engine damage.

Never perform cleaning operations when the truckmount engine is running at the
IDle throttle position. failure to do so will increase the risk of serious component
or engine damage.

Never operate the truckmount with the vehicle doors closed. Doing so results in
extremely high temperatures inside the vehicle and will lead to serious component
or engine damage.

Never use concentrated acids or solvents (including d-limonene) in the truckmount
water system or chemical system. Use of these products will cause serious
component damage.

Never operate the truckmount with a water hardness reading measuring 3.0 grains
per gallon (3.79 litres) or higher. Using reading than 3.0 grains per gallon (3.79
litres) will cause scale to build up inside the truckmount water system. Scale build
up causes serious component damage. Test all water prior to use and use water
softening equipment if necessary.

«
...
13
14
15
16
17
...
»

Содержание Steamatic 8800 TMU





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Steamatic 8800 TMU

Бренд: Datavideo Страницы: 50

Бренд: Waterous Страницы: 90

Бренд: Campbell Страницы: 14

Бренд: ICS ELECTRONICS Страницы: 6

Бренд: Ecco Страницы: 2

Бренд: Landoll Страницы: 94

Бренд: Baileigh Industrial Страницы: 12

Бренд: Zero 88 Страницы: 12

Бренд: Zeiss Страницы: 119

Бренд: Zehnder Rittling Страницы: 32

Бренд: Qlight Страницы: 4

Бренд: Tadano Страницы: 16

Aristo WeldCloud Mig U5000i

Бренд: ESAB Страницы: 28

Бренд: Major tech Страницы: 12

Бренд: Tripp Lite Страницы: 24

Бренд: BRAND Страницы: 21

Бренд: Milestone Страницы: 40

Firefly 808 Universal

Бренд: Phonic Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды