HydraMaster Steamatic 8800 TMU Скачать руководство пользователя страница 19

Страница: 19 / 148

1-11 - General Information

Steamatic 8800 TMU

Training
The distributor should provide a thorough review of the operation manual with the
purchaser along with instruction and familiarization in:

How all the truckmount’s systems function.

All safety precautions and their importance.

How to correctly start and shut down the truckmount.

How to correctly clean with the truckmount.

Where and how often to check and change component oil levels.

freezing damage and how to avoid it. This includes explaining proper freeze

guarding procedures.
How to do basic troubleshooting of the truckmount.

Hard water damage and how to avoid it. This includes how to determine if hard

water exists in your area and the installation and use of water softening systems.
The truckmount’s warranty and warranty procedures.

Содержание Steamatic 8800 TMU





















































































































































Результаты поиска

Содержание Steamatic 8800 TMU

Отзывы:

HydraMaster Steamatic 8800 TMU, Руководство пользователя, Страница: 19 / 148

Результаты поиска

Содержание Steamatic 8800 TMU

Отзывы: