HydraMaster Steamatic 8800 TMU Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 148

HydraMaster Steamatic 8800 TMU Скачать руководство пользователя страница 29

2-3 - Installation Information

Steamatic 8800 TMU

Use caution when drilling any holes through the van floor. Many vans have critical

components mounted directly below the vehicle floor that could be damaged by

a misplaced drill bit.

loCatIng tHe SteamatIC 8800 tmu In VeHICle

There are two recommended entry points on the vehicle for the Steamatic 8800 TMU
installation: the side door or the rear doors.

Most installations are through the side door. This provides rear access for accessories
and hoses as well as unobstructed access to the component/working side of the machine,
thus making it a bit easier to perform maintenance and/or repair without removing the unit
from the truck.

Rear mounting requires the unit to be slid to the right side as far as possible Although
installing the Steamatic 8800 TMU through the rear door partly limits working access, it
does direct the noise away from the cleaning site.

In addition, rear mounting not only provides adequate working space on the component
side of the unit but also improves weight distribution inside the van (engine and component
weight line up over drive shaft). Some cleaners in colder geographical areas prefer this
placement for better traction in ice and snow. Also, it is physically easier to load the unit
into the rear door due to the height of the vehicle bed.

Secure Installation

No matter how the unit is installed, check to see if the Steamatic 8800 TMU is properly

secured to the floor of the van with the hardware provided. This safety measure will ensure

that the machine will not slide inside the van. See figure 2-2 for the correct installation.

figure 2-2. recommended location of

Steamatic 8800 tmu in Van

«
...
27
28
29
30
31
...
»

Содержание Steamatic 8800 TMU





















































































































































Отзывы:

Нет отзывов