HydraMaster Steamatic 8800 TMU Скачать руководство пользователя страница 54

Страница: 54 / 148

Machine Maintenance

5-12

Steamatic 8800 TMU

Remove the stainless steel plunger bolt and ceramic plunger from the plunger guide

15.

(see figure 5-9).
If the slinger washer is removed, be certain it is re-installed or replaced.

16.

Separate plunger bolt from ceramic plunger (see

17.

figure 5-9).

Install new Teflon

18.

back-up ring and O-ring on the plunger bolt. Apply a film of O-ring

grease on the outside of the o-ring (see figure 5-10).

Apply removable anaerobic thread sealant (loctite

19.

542) to the threads of the plunger

bolt, carefully pressing the plunger bolt into ceramic plunger (see figure 5-10).
Slide new ceramic plunger over the plunger guide (see

20.

figure 5-10).

Torque plunger to 14.5 ft. lbs (2 m kgs).

21.

figure 5-9. remove Stainless Steel plunger Bolt and Ceramic plunger

figure 5-10. Install o-ring, apply Sealant and Slide plunger over plunger guide

Содержание Steamatic 8800 TMU





















































































































































Результаты поиска

Содержание Steamatic 8800 TMU

Отзывы:

HydraMaster Steamatic 8800 TMU, Руководство пользователя, Страница: 54 / 148

Результаты поиска

Содержание Steamatic 8800 TMU

Отзывы: