HydraMaster Steamatic 8800 TMU Скачать руководство пользователя | Manualshive

Страница: 14 / 148

background image

General Information

-

1-6

Steamatic 8800 TMU

Warnings and Cautions specific to the Steamatic 8800 TMU include the following:

During the operation of the truckmount many components are in motion. Never
touch any part of the truckmount that is in motion. Serious injury may result.

During the operation of the truckmount many surfaces will become extremely hot.
Never touch hot surfaces. Serious injury may result.

The operation of this truckmount can produce noise levels exceeding 85 decibels
to a distance of 10 ft (3.05 m). The occupational Safety and Health Administration
(oSHA) recommends the use of hearing protective equipment if a person is
exposed to an average of 85 decibels over an 8-hour period. Check with local
and state agencies concerning hearing conservation rules.

During the operation of the truckmount carbon monoxide and other toxic fumes
are produced. Position the vehicle so that any fumes produced will be directed
away from inhabited areas and any points of building entry (doors, windows, air
conditioning units, fans, etc.). Do not occupy the vehicle while the truckmount is
in operation. Serious injury may result.

During the operation of the truckmount, chemicals known to the State of California
to cause cancer, birth defects and other reproductive harm are produced by the
engine exhaust.

Never operate the truckmount with a portable gas container inside the vehicle.

Doing so will increase the risk of fire and explosion. Serious injury or death may

result.

Transporting a vented fuel container that presently contains, or has ever contained

in the past, a flammable liquid is strictly forbidden by The manufacturer and by

federal and state regulations. Doing so will increase the risk of fire and explosion.

Serious injury or death may result.

«
...
12
13
14
15
16
...
»

Содержание Steamatic 8800 TMU





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Steamatic 8800 TMU

Бренд: Zetec Страницы: 23

Бренд: CAB Страницы: 13

Бренд: CAB Страницы: 30

Бренд: CAB Страницы: 17

Бренд: CAB Страницы: 33

Camping Equipment

Бренд: C. Crane Страницы: 8

Бренд: C-Pro Direct Страницы: 4

Бренд: C-Pro Direct Страницы: 4

Бренд: dbx Страницы: 2

Бренд: Eagle Group Страницы: 8

Бренд: Garelick Страницы: 2

Бренд: Garelick Страницы: 2

PORTABLE ICE FISHING KIT

Бренд: Garmin Страницы: 5

Бренд: Hantek Страницы: 124

Бренд: Hameg Страницы: 10

Бренд: IDEAL Networks Страницы: 60

Бренд: IceCure Страницы: 104

Бренд: Magma Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды