HydraMaster Steamatic 8800 TMU Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 148

HydraMaster Steamatic 8800 TMU Скачать руководство пользователя страница 30

Installation Information

-

2-4

Steamatic 8800 TMU

A sudden or crash stop will cause the machine to rocket forward if not properly
secured. To prevent serious personal injury, ensure that the Steamatic 8800 TMU

is well secured to the floor of the vehicle with the hardware supplied. Protect

yourself and the machine.

The manufacturer strongly recommends that the exhaust from the front of the
machine be vented down under the truck to prevent carbon monoxide from
entering the job site.

always park the truck so the exhaust is blowing away

from the job site

.

Never operate this machine with a portable gas can inside the truck. Doing so

increases the risk of a fire or explosion.

Mount a fire extinguisher just inside the rear or side door for emergencies.

Do not use a portable propane tank inside of the truck or van. It is dangerous and
illegal in most states.

Transporting any vented fuel container that presently holds or has ever held

a flammable liquid in a vehicle containing the Steamatic 8800 TMU is strictly

forbidden by The manufacturer and by federal and state regulation.

The engine exhaust from this product contains chemicals known to the State of
California to cause cancer, birth defects or other reproductive harm.

«
...
28
29
30
31
32
...
»

Содержание Steamatic 8800 TMU





















































































































































Отзывы:

Нет отзывов