HydraMaster Steamatic 8800 TMU Скачать руководство пользователя страница 11

Страница: 11 / 148

1-3 - General Information

Steamatic 8800 TMU

SyStem ConCept

This is how the Steamatic 8800 TMU works:

Incoming water enters the water box and is pressurized by the high pressure water

pump. The water is heated by engine coolant in the tube and shell heat exchanger

and then by the engine and blower exhaust in the cross flow heat exchanger.

Cleaning solution is then injected into the pressurized water stream and the heated

solution is delivered to the cleaning tool.
The solution is recovered by the vacuum generated by the vacuum pump and is

collected in the recovery tank for proper disposal.

Photographs and illustrations included in this document can represent optional
equipment as well as standard equipment.

Water Box

Water pump

Heat

exchangers

Silencer

engine

Vacuum Blower

Содержание Steamatic 8800 TMU





















































































































































Результаты поиска

Содержание Steamatic 8800 TMU

Отзывы:

HydraMaster Steamatic 8800 TMU, Руководство пользователя, Страница: 11 / 148

Результаты поиска

Содержание Steamatic 8800 TMU

Отзывы: