HydraMaster Steamatic 8800 TMU Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 148

HydraMaster Steamatic 8800 TMU Скачать руководство пользователя страница 46

Machine Maintenance

-

5-4

Steamatic 8800 TMU

oVerall maCHIne maIntenanCe

Maintenance, troubleshooting and repair are much easier tasks to accomplish on a clean
truckmount. Regular cleaning of the truckmount offers the user an opportunity to visually
inspect all facets of the truckmount and spot potential problems before they occur. In
addition to the operational maintenance the following “housekeeping” duties should be
performed.

after each job

Check the recovery tank and the recovery tank filters. Empty and clean as

•

necessary.

daily

Wipe the truckmount down thoroughly with a damp cloth.

•

Wipe down the vacuum and high pressure hoses as needed.

•

Inspect and clean the vacuum slot on the cleaning wand.

•

Check the wand head for sharp edges that could tear carpet. file down as needed.

•

Clean the wand to maintain original appearance.

•

Visually inspect the hoses for abrasions, cuts, etc. Repair or replace as needed.

•

Weekly

empty the chemical container. Wash out thoroughly to remove any chemical buildup.

•

Inspect the chemical feed line strainer and use solution of equal parts white vinegar

•

and water to remove any chemical buildup.
Thoroughly clean the wand and inspect for clogged jets, debris in vacuum slot and

•

leaking fittings at valve.

Thoroughly clean the vacuum and high pressure hoses including quick releases and

•

cuffs.

«
...
44
45
46
47
48
...
»

Содержание Steamatic 8800 TMU





















































































































































Отзывы:

Нет отзывов