HydraMaster Steamatic 8800 TMU Скачать руководство пользователя

Страница: 40 / 148

Operating Instructions

4-4

Steamatic 8800 TMU

Start-up proCedure

Perform all daily periodic maintenance as specified in this Owner’s Manual.

Connect a garden hose to supply water to the truckmount. Push the “PUMP-IN”

switch to the “oN” position.
Connect the cleaning wand or tool to the length of hose required to perform the

cleaning job.
Start the truckmount with:

The throttle switch in the “IDle” position.

The “PUMP ClUTCH” switch in the “off” position.

After the engine starts, allow the truckmount to run in “IDle” for 2 - 3 minutes to

warm up.

Never clean when the Steamatic 8800 TMU is in the “IDle” mode. failure to
follow this caution may result in serious component or engine damage.

Press the throttle switch to “MID” or “HIGH”.

Press the “PUMP ClUTCH” switch to the “PUMP oN HeAT MoDe” position for

carpet cleaning or upholstery cleaning; for high pressure washing, press “PUMP oN
No HeAT”
Set the “HeAT SeleCToR” valve to the

desired position.

Set to the “WARM” position for upholstery

cleaning.
Set to the “HoT” position for carpet

cleaning.

Press the “AUTo PUMP-oUT” switch to the

“oN” position.

SettIng tHe preSSure

lower  the  pressure  below  1,200  psi  prior  to
moving the “WATeR PReSSURe SeleCToR”
valve  to  “Carpet  Cleaning”  mode  (see
figure  4-6).  failure  to  do  so  may  result  in
serious component or engine damage.

location of Water

figure 4-6.

pressure Selector Valve

(labels Shown as part of the
High pressure Washing kit -

Содержание Steamatic 8800 TMU





















































































































































Результаты поиска

Содержание Steamatic 8800 TMU

Отзывы:

Похожие инструкции для Steamatic 8800 TMU

Бренды по названию

Популярные бренды

HydraMaster Steamatic 8800 TMU, Руководство пользователя

Результаты поиска

Содержание Steamatic 8800 TMU

Отзывы:

Похожие инструкции для Steamatic 8800 TMU

Бренды по названию

Популярные бренды