HydraMaster Steamatic 8800 TMU Скачать руководство пользователя страница 86

Страница: 86 / 148

Systems Troubleshooting

8-4

Steamatic 8800 TMU

engIne

the engine will not turn over

1.1. A loose or corroded
battery terminal.

Clean and tighten the battery terminal connections.

1.2. The battery is dead.

Recharge or replace the battery. Test the charging system.
Repair if necessary.

Do not attempt to jump start the truckmount from
a running vehicle. The amperage output from an
automobile will damage the charging system of the
truckmount.

1.3. The main fuse is
blown.

Check the main fuse.

If the fuse is blown, inspect the electrical system for worn
or shorted wires. Repair or replace as necessary.

1.4. The vacuum blower
has seized.

Attempt to turn the coupler by hand. If it will not turn refer
to the Vacuum System Troubleshooting Subsection.

1.5. The ignition switch is
faulty.

Test to see if there is power both to and from the switch.
Refer to the electrical Section of this manual.

1.6. The starter solenoid
is faulty.

Test to see if there is power to solenoid with ignition in
"START" position. Refer to electrical Section.

1.7. The starter motor is
faulty.

Test to see if there is power to the motor with the ignition in
"START" position. Refer to the electrical Section.

1.8. None of the above.

Refer to a qualified service technician for further

troubleshooting.

Содержание Steamatic 8800 TMU





















































































































































Результаты поиска

Содержание Steamatic 8800 TMU

Отзывы:

HydraMaster Steamatic 8800 TMU, Руководство пользователя, Страница: 86 / 148

Результаты поиска

Содержание Steamatic 8800 TMU

Отзывы: