HydraMaster Steamatic 8800 TMU Скачать руководство пользователя страница 12

Страница: 12 / 148

General Information

1-4

Steamatic 8800 TMU

ContaCt InformatIon

If you have any questions regarding the operation, maintenance or repair of this machine,
please contact your local distributor.

To find a local distributor, please visit our website at

http://www.hydramaster.com/owners/

locate/index.asp.

If your question cannot be resolved by your distributor or by the information within this
manual, you may contact HydraMaster Customer Service direct using the following phone
numbers.

Hours

telephone numbers

e-mail addresses

Monday-friday

(425) 775-7275 Service

Tech Support:

[email protected]

7:00 a.m. to 5:00 p.m.

(425) 775-7276 Parts

Parts Support:

[email protected]

Pacific Standard Time

(800) 426-4225 Parts /

Service fAX

When calling your distributor, be sure to reference the serial number and date of
purchase.

foR yoUR RefeReNCe:

Serial No. ____________________________________________________

Date of Purchase: _____________________________________________

Purchased from (Distributor): ____________________________________

Содержание Steamatic 8800 TMU





















































































































































Результаты поиска

Содержание Steamatic 8800 TMU

Отзывы:

HydraMaster Steamatic 8800 TMU, Руководство пользователя, Страница: 12 / 148

Результаты поиска

Содержание Steamatic 8800 TMU

Отзывы: