manualshive.com logo in svg

Huawei UPS2000-G-10KRTLV2, Руководство пользователя, Страница: 95 / 158

Поделиться
Скачать
Huawei UPS2000-G-10KRTLV2 Скачать руководство пользователя страница 95

UPS2000-G-(3 kVA-20 kVA)-V2 
User Manual (Two Live Wires) 

6 Communications 

 

Issue 07 (2019-12-19) 

Copyright © Huawei Technologies Co., Ltd. 

88 

 

 

Works with NetShutdown, a computer and server security shutdown program developed 
by Huawei, to automatically shut down the computers and servers where NetShutdown is 
installed to protect customer data and reduce loss. 

 

Works with RCCMD, a client shutdown software developed by Generex, to 
automatically and safely shut down the client that is installed with the RCCMD, thereby 
protecting customers' data and preventing loss. 

 

Alarm information is sent to the specified user mailbox at the specified time. 

6.3 Modbus Card 

The RMS-MODBUS01A provides an RS485 networking solution to remotely manage the 
UPS. 

The card implements the following functions by setting the DIP switches: 

 

Selects the Modbus protocol by using a DIP switch over the RS485 communications 
protocol. 

 

Uses a DIP switch to select a two-wire or four-wire system. 

 

Provides a DIP switch to select a build-out resistor. 

 

Provides a DIP switch for setting the optional card address. 

 

Supports hot swap. 

6.4 Dry Contact Card 

The RMS-RELAY01A is installed in an optional card slot and supports hot swap. 

The dry contact card provides six alarm dry contact outputs (normal mode, battery mode, 
bypass mode, low battery voltage, bypass backfeed, and UPS faults) and two dry contract 
control inputs (one is the shutdown signal input, and the other is reserved). 

Содержание UPS2000-G-10KRTLV2































































































































































Отзывы:

Нет отзывов