manualshive.com logo in svg

Huawei UPS2000-G-10KRTLV2, Руководство пользователя, Страница: 100 / 158

Поделиться
Скачать
Huawei UPS2000-G-10KRTLV2 Скачать руководство пользователя страница 100

UPS2000-G-(3 kVA-20 kVA)-V2 
User Manual (Two Live Wires) 

7 Routine Maintenance 

 

Issue 07 (2019-12-19) 

Copyright © Huawei Technologies Co., Ltd. 

93 

 

Item 

Expected Result 

Measures 

Maintenance Interval 

batteries 

the insulation layer does 
not crack. 

Battery volta 

 

Equalized charging 
voltage: 14.1 V ± 0.1 
V 

 

Float charging 
voltage: 13.5 V ± 0.1 
V 

1.

 

Check whether the 
equalized charging 
voltage and float charging 
voltage of a battery are 
normal. 

2.

 

If the charging voltage of 
a battery exceeds the 
specifications 
requirement, perform a 
complete forcible 
equalized charging for the 
battery, and check again 
whether the voltage is 
normal. 

3.

 

If the fault persists, 
contact Huawei technical 
support. 

Quarterly 

Shallow 
discharge test 
(recommended) 

Conduct a shallow 
discharge test when the 
UPS is backed up to 
verify that the batteries 
can discharge normally. 

1.

 

Locate the cause when an 
exception is identified. 

2.

 

If the fault persists, 
contact Huawei technical 
support. 

Quarterly 

Capacity Test 
(recommended) 

When the UPS is backed 
up, discharge a battery to 
the undervoltage alarm 
threshold, to refresh the 
capacity of the battery. 

1.

 

Locate the cause when an 
exception is identified. 

2.

 

If the fault persists, 
contact Huawei technical 
support. 

Yearly 

Battery 
connection 
reliability 

1.

 

Each battery terminal 
is connected reliably. 
(When battery strings 
are powered off, 
check the reliability 
of each terminal in 
the order from 
positive terminals to 
negative terminals.) 

2.

 

The tightening torque 
of each battery screw 
meets the 
requirements of the 
battery manufacturer. 
(A torque wrench is 
used for checking the 
torque. After 
checking that the 
battery screws meet 
the requirements, 
mark the screws for 

1.

 

Rectify any abnormal 
connection. 

2.

 

If the fault persists, 
contact Huawei technical 
support. 

Yearly 

Содержание UPS2000-G-10KRTLV2































































































































































Отзывы:

Нет отзывов