Huawei UPS2000-G-10KRTLV2 Скачать руководство пользователя страница 74 | Manualshive

Страница: 74 / 158

Huawei UPS2000-G-10KRTLV2 Скачать руководство пользователя страница 74

UPS2000-G-(3 kVA-20 kVA)-V2
User Manual (Two Live Wires)

4 Control Panel

Issue 07 (2019-12-19)

Copyright © Huawei Technologies Co., Ltd.

67

Maximum number of bypass transfers within 30 minutes. The value ranges from 1
to 3. The default value is 3. When the number of bypass transfers exceeds the
maximum, the UPS keeps running is bypass mode (in ECO mode, the UPS keeps
running in normal mode). The parameter is configurable after the inverter shuts
down.

Do not set the UPS to ECO mode when the system output connects to an isolated transformer.

−

Output transformer

parameter

If an output transformer is connected, set the parameter to

Enabled

; otherwise, set

it to

Disabled

. The values include

Disabled

and

Enabled

. The default value is

Disabled

. The parameter is configurable after the inverter shuts down.

When you install a transformer on the output side, you are advised to connect the load to the pL terminal
and disable power segment.

−

Generator mode

parameter

The values include

Weak adaptability mode

,

Balance mode

, and

Strong

adaptability mode

. The default value is

Balance mode

. When the mains input

voltage quality is good, select

Weak adaptability mode

; when the quality is

average (for example, the mains input is from a high-performance generator or a
common power grid), select

Balance mode

; when the quality is poor (for example,

the mains input is from a common generator), select

Strong adaptability mode

.

The parameter is configurable after the inverter shuts down.

−

Auto check bus capa.

parameter

Determine whether to automatically check the bus capacitance upon power-on and
generate capacitance failure warnings. The values include

Disabled

and

Enabled

.

The default value is

Enabled

. If the value is

Enabled

, UPS startup takes additional

30–180 seconds. The parameter is configurable after the inverter shuts down.

−

Auto start

parameter

Determine whether to automatically start inverter output after the UPS connects to
the mains. The values include

Disabled

and

Enabled

. The default value is

Disabled

.

The parameter is configurable after the inverter shuts down.

−

No battery alarm

This parameter is set to

Enabled

by default. If it is set to

Disabled

, the

No battery

alarm

will not be reported. This parameter automatically changes to

Enabled

after

batteries are connected. It is configurable only when batteries are not connected.

If the batteries have been connected and you try to set this parameter, a message "Batteries have been
connected. This parameter cannot be set." will be displayed.

Battery Parameters Screen

«
...
72
73
74
75
76
...
»

Содержание UPS2000-G-10KRTLV2































































































































































Отзывы:

Нет отзывов