Huawei UPS2000-G-10KRTLV2 Скачать руководство пользователя страница 136

Страница: 136 / 158

UPS2000-G-(3 kVA-20 kVA)-V2
User Manual (Two Live Wires)

C Alarm Handling

Issue 07 (2019-12-19)

129

Alarm ID
(Alarm
ID-Alarm
Cause)

Alarm
Name

Alarm
Level

Alarm Clear
Mode

Impact on the
System

Repair Proposal



Clean off the foreign
objects around the fan. If
the alarm persists, contact
Huawei technical support
for repair.

0040-09

Rectifier fault

Critical Power-off clear

The rectifier
transfers to
battery mode,
and the power
supply is not
affected.

If no battery is
installed, the
UPS shuts down.

The UPS
transfers to
another working
mode or shuts
down.

Possible cause: The rectifier
is faulty.

Measure: Contact Huawei
technical support for repair.

0040-10

Rectifier fault

Critical Manual

clear/Power-off
clear

The UPS shuts
down.

Possible cause: The digital
signal processing (DSP) or
complex programmable
logical device (CPLD) chip
is faulty.

Measure: Contact Huawei
technical support for repair.

0041-01

Rectifier
alarm

Minor

Manual
clear/Power-off
clear

N/A

Possible cause: The
EEPROM chip is faulty.

Measure: Contact Huawei
technical support for repair.

0041-02

Rectifier
alarm

Minor

Automatic clear

The UPS shuts
down.

The UPS may
transfer to
another working
mode or shut
down.

Possible cause: The
single-side bus capacitor is
faulty.

Measure: Contact Huawei
technical support for repair.

0041-03

Rectifier
alarm

Minor

Manual
clear/Power-off
clear

The power
supply from the
UPS and system
is not affected.

Possible cause: The bus
capacitor is faulty.

Measure: Contact Huawei
technical support for repair.

0041-10

Rectifier
alarm

Minor

Automatic clear

N/A

Possible cause: The load
power exceeds the loading

Содержание UPS2000-G-10KRTLV2































































































































































Результаты поиска

Содержание UPS2000-G-10KRTLV2

Отзывы:

Huawei UPS2000-G-10KRTLV2, Руководство пользователя, Страница: 136 / 158

Результаты поиска

Содержание UPS2000-G-10KRTLV2

Отзывы: