manualshive.com logo in svg

Huawei UPS2000-G-10KRTLV2, Руководство пользователя, Страница: 145 / 158

Поделиться
Скачать
Huawei UPS2000-G-10KRTLV2 Скачать руководство пользователя страница 145

UPS2000-G-(3 kVA-20 kVA)-V2 
User Manual (Two Live Wires) 

C Alarm Handling 

 

Issue 07 (2019-12-19) 

Copyright © Huawei Technologies Co., Ltd. 

138 

 

Alarm ID 
(Alarm 
ID-Alarm 
Cause) 

Alarm 
Name 

Alarm 
Level 

Alarm Clear 
Mode 

Impact on the 
System 

Repair Proposal 

Measure: Restart the UPS 
after the alarm is cleared. 

0094-01 

Redundancy 
failure 

Minor 

Automatic clear 

N/A 

Possible causes: 

 

The configured number 
of redundant UPSs 
exceeds the maximum 
allowed value. 

 

The load exceeds the 
rated loading capacity of 
the requisite UPSs in the 
parallel system. 

Measures: 

 

Reduce the number of 
redundant UPSs or set the 
system to be 
non-redundant. 

 

Reduce the load or 
replace the UPS with a 
larger-capacity UPS. 

0096-01 

Abnormal 
ECO volt. 

Minor 

Automatic clear 

Transfer to 
bypass mode is 
prohibited. If the 
bypass is 
supplying power, 
the UPS transfers 
to another 
working mode. 

Possible cause: The ECO 
input is abnormal. 

Measure: Check whether the 
ECO input voltage or 
frequency exceeds the 
configured range. If yes, 
change the range or wait 
until the bypass input 
recovers. 

0105-05 

Comm. 
failed. 

Minor 

Automatic clear 

The monitoring 
module cannot 
monitor the 
digital signal 
processor (DSP) 
of the power 
module. 

Possible causes: 

 

The communications 
cable is faulty. 

 

An internal fault occurs 
in the UPS. 

Measures: 

 

Check the 
communications cable. 

 

Contact Huawei technical 
support for repair. 

0125-01 

Incon. paral. 
param. 

Critical  Automatic clear 

An alarm is 
generated, and 
all the UPSs in 
the parallel 
system cannot 

Possible cause: The parallel 
parameters are not set 
consistently on the UPSs. 

Measure: Set the parallel 
parameters consistently, or 

Содержание UPS2000-G-10KRTLV2































































































































































Отзывы:

Нет отзывов