Huawei UPS2000-G-10KRTLV2 Скачать руководство пользователя страница 128

Страница: 128 / 158

UPS2000-G-(3 kVA-20 kVA)-V2
User Manual (Two Live Wires)

C Alarm Handling

Issue 07 (2019-12-19)

121

Alarm ID
(Alarm
ID-Alarm
Cause)

Alarm
Name

Alarm
Level

Alarm Clear
Mode

Impact on the
System

Repair Proposal

down.



The UPS may
transfer to
another
working
mode or shut
down.

0005-01

Mains neutral
loss

Minor

Automatic clear



The UPS
transfers to
battery mode.



If no battery
is equipped,
the UPS shuts
down.



The UPS
changes the
working
mode or shuts
down.

Possible cause: The mains
input neutral wire is not
connected.

Measure: Check that mains
input power cables are
correctly connected.

0007-01

Batt. trans.
overlimit

Minor

Manual
clear/Power-off
clear/Automatic
clear

The UPS does
not transfer back
to normal mode
even when the
mains is normal.

Possible cause: The mains
voltage fluctuates frequently.
The UPS has transferred
from normal mode to battery
mode within 2 minutes for
10 consecutive times. The
rectifier locks out in battery
mode.

Measure: Check the mains.

0008-01

Rect. start
overlimit

Minor

Manual
clear/Power-off
clear

The UPS cannot
start.

Possible cause: The mains
voltage frequently becomes
abnormal during startup.

Measure: Check the mains
input voltage. If the voltage
becomes normal, clear the
alarm and restart the UPS.

0010-01

Abnormal
BPS volt.

Minor

Automatic clear

The UPS cannot
transfer to bypass
mode. If the
bypass is
supplying power,
the UPS changes
the working
mode.

Possible causes:



The bypass input voltage
is abnormal.



The bypass input
frequency is abnormal.

Measures:



Check whether the bypass
input voltage exceeds the
configured range. If yes,

0010-02

Abnormal
BPS volt.

Minor

Содержание UPS2000-G-10KRTLV2































































































































































Результаты поиска

Содержание UPS2000-G-10KRTLV2

Отзывы:

Huawei UPS2000-G-10KRTLV2, Руководство пользователя, Страница: 128 / 158

Результаты поиска

Содержание UPS2000-G-10KRTLV2

Отзывы: