Huawei UPS2000-G-10KRTLV2 Скачать руководство пользователя страница 131

Страница: 131 / 158

UPS2000-G-(3 kVA-20 kVA)-V2
User Manual (Two Live Wires)

C Alarm Handling

Issue 07 (2019-12-19)

124

Alarm ID
(Alarm
ID-Alarm
Cause)

Alarm
Name

Alarm
Level

Alarm Clear
Mode

Impact on the
System

Repair Proposal

Measures:



Check battery parameter
settings.



Disconnected the external
battery charger, check
whether the alarm is
cleared. If not, contact
Huawei technical support
for repair.

0026-01

Batt.
undervolt.

Minor

Automatic clear

An alarm is
generated, and
the system may
shut down due to
EOD.

Possible cause: The mains
input is abnormal. Battery
discharge results in a low
battery voltage.

Measure: If possible, connect
to the mains power when the
UPS is in non-battery test
state.

0027-01

Batt.
overcurrent

Minor

Automatic clear

An alarm is
generated, and
the battery
lifespan is
affected.

Possible causes: The charger
is abnormal.

Measure: Contact Huawei
technical support for repair.

0028-01

Breaker OFF

Critical Automatic clear

N/A

Possible causes:



The mains input power
cables are incorrectly
connected.



The mains input circuit
breaker is OFF.

Measure: Check whether
mains input power cables are
correctly connected. If yes,
switch on the mains input
circuit breaker.

0028-02

Breaker OFF

Critical Automatic clear

N/A

Possible causes:



The bypass is
short-circuited or the
bypass input experiences
overcurrent.



The bypass input circuit
breaker is OFF.

Measures:



Check whether the bypass
output load is
short-circuited using a

Содержание UPS2000-G-10KRTLV2































































































































































Результаты поиска

Содержание UPS2000-G-10KRTLV2

Отзывы:

Huawei UPS2000-G-10KRTLV2, Руководство пользователя, Страница: 131 / 158

Результаты поиска

Содержание UPS2000-G-10KRTLV2

Отзывы: