Huawei eSpace IAD Скачать руководство пользователя страница 78 | Manualshive

Страница: 78 / 109

background image

eSpace IAD
Troubleshooting

3 Co mmon Troubleshooting Methods

Issue 02 (2012-02-29)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

73

IAD2000(config)#display alarm history alarmid 0x06020007
Command:
        display alarm history alarmid 0x06020007
  ALARM 269 RECOVERY WARNING 0x06020007 COMMUNICATION 2010 -12-09 10:25:16
  ALARM NAME  : Network-autocheck restore
  PARAMETERS  : netcheck-ip : 192.163.1.8
  DESCRIPTION : Network-autocheck restore //Restore indicates network resumption
  CAUSE       : Network restore
  ADVICE      : Need no process.
  --- END

Step 7

Run the command to query the users' registration state. The state is

registered

.

The command is as follows:

TERMINAL(config)#display sip attribute 0
                Sip User Information
-----------------------------------------------------
user-sn            : 0
id                 : +8657187900066
password           : ********
name               : [email protected]
local address      : 192.163.1.47
local-port         : 5060
registration state : registered //The user is registered
expire-time        : 0 sec
previous server    :
current server     : 192.163.1.8 : 5060
dm match delay     : 0 ms
digit-map position : remote
dial-delay position: remote
support no pound   : off
group id           : -
......
TERMINAL(config)#

display sip attribute slot 0 port 0

                Sip User Information
-----------------------------------------------------
user-sn            : 0-0
id                 : 81151
local address      : 192.163.1.26
registration state : registered
expire-time        : 120 sec
previous server    : -
current server     : 192.163.1.8 : 5060
local-port         : 5060
name               : -
password           : ********
dm match delay     : 200 ms
digit-map position : remote
dial-delay position: remote
support no pound   : off
group id           : -
port type          : FXS
ShortNum           : -
-----------------------------------------------------

----End

«
...
76
77
78
79
80
...
»

Содержание eSpace IAD














































































































Отзывы:

Нет отзывов

Похожие инструкции для eSpace IAD

Бренд: ABB Страницы: 138

Бренд: ABB Страницы: 116

Бренд: IN-COMMAND Страницы: 47

Бренд: Audio Control Страницы: 36

Бренд: Kramer Страницы: 4

RealPresence Centro

Бренд: Polycom Страницы: 53

Бренд: Greenheck Страницы: 16

RealPresence Utility Cart 500

Бренд: Polycom Страницы: 10

Zynq UltraScale+

Бренд: Xilinx Страницы: 86

Бренд: Roadstar Страницы: 21

Бренд: Elenberg Страницы: 36

Бренд: Panasonic Страницы: 8

SCEN15 - DESKTOP CD AUDIO SYS

Бренд: Panasonic Страницы: 8

SCEN33 - CD STEREO SYSTEM

Бренд: Panasonic Страницы: 8

Бренд: Panasonic Страницы: 28

Бренд: Panasonic Страницы: 27

Бренд: Panasonic Страницы: 19

Бренд: Panasonic Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды