Huawei eSpace IAD Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 109

background image

eSpace IAD
Troubleshooting

2 Analy zing and Rectify ing Faults

Issue 02 (2012-02-29)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

56



If yes, go to



If no, modify the configuration.

Step 4

Check whether the fault is rectified.



If yes, the procedure ends.



If no, go to

Step 5

Contact Huawei technical support.

----End

2.3.22 Unable to Run Commands

Symptom

The commands can be entered but cannot be run. Whenever a command is run, a message is
displayed indicating that the system is busy and the command cannot be run.

Cause

Exceptions occur when commands are being run.

Solution

1.

Press the Reset button to restart the device. (Do not turn off the power or the operation
log will be lost.)

2.

Pull off power supply, and then power on the device to restart it.

3.

After the system is restarted, run the

display log

command to view the operation log, run

the

display alarm history all

command to view the alarms, and enter the diagnose mode

to view the exceptions.

4.

Run a command again. If the command cannot be run, go to the next step.

5.

Contact Huawei technical support.

2.3.23 Serial Port Failure

Symptom

After logging in to the IAD through the serial port, you cannot enter anything through the
keyboard. In addition, no output or only illegible character is generated.

Cause

The possible causes are as follows:



The scroll lock is on.



If no output is generated, the serial cable may not be well connected.



If illegible characters are generated, the fault may be caused by incorrect parameter
configuration.



The system is down.

«
...
59
60
61
62
63
...
»

Содержание eSpace IAD














































































































Отзывы:

Нет отзывов

Похожие инструкции для eSpace IAD

Бренд: zipwake Страницы: 12

Бренд: jbc Страницы: 12

Бренд: Samsung Страницы: 70

Бренд: Samsung Страницы: 21

Бренд: Samsung Страницы: 28

Бренд: Samsung Страницы: 22

OneFlow OFTWH-R

Бренд: Watts Страницы: 8

Бренд: Lincoln Electric Страницы: 2

Бренд: Daewoo Страницы: 21

Бренд: DAEWOO ELECTRONICS Страницы: 7

Бренд: AbleNet Страницы: 8

Бренд: HK Audio Страницы: 105

Бренд: Audiovox Страницы: 15

Voiceducer MDRMN4044

Бренд: Motorola Страницы: 18

Бренд: Motorola Страницы: 18

Бренд: Motorola Страницы: 58

Бренд: Motorola Страницы: 7

Бренд: Brahler Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды