Huawei eSpace IAD Скачать руководство пользователя страница 67

Страница: 67 / 109

eSpace IAD
Troubleshooting

3 Co mmon Troubleshooting Methods

Issue 02 (2012-02-29)

Huawei Proprietary and Confidential

Indicat
or

Colo
r

Item

Status

Description

PHON
E 4

port
indicator

Blinking (1.5s on
and 0.5s off)

Indicates that the system is
switched over to the backup PSTN
and the phone is in use.

Indicates that the phone is picked
up or the phone is in lock state.

Off

Indicates that the phone of the
corresponding port is in hang-up
state.

The numbers of the voice telephone interface indicators of the IAD101H, 102H, and 104H are 1, 2, and
4 respectively.

Indicators of the IAD208E(M)

Indicator

Name

Abnormal
Status

Fault Type

Cause and

Rectification
Method

POWER
indicator

PWR

Off when the
IAD is powered
on

System fault:
The IAD failed
to start.

If the AC power
supply is
normal and
cables are
connected, the
internal power
module of the
IAD is faulty.
The IAD needs
to be repaired.

RUN indicator

RUN

Off when the
IAD is powered
on

System fault:
The IAD does
not respond or
the serial port is
faulty.

Press the
Reset button
to restart the
device (Do
not turn off
the power;
otherwise,
the alarm
log will be
lost.)

Run the

display
alarm
history all

command to
view the
alarm
information.

Содержание eSpace IAD














































































































Результаты поиска

Содержание eSpace IAD

Отзывы:

Похожие инструкции для eSpace IAD

Бренды по названию

Популярные бренды

Huawei eSpace IAD, Руководство по устранению неисправностей

Результаты поиска

Содержание eSpace IAD

Отзывы:

Похожие инструкции для eSpace IAD

Бренды по названию

Популярные бренды