Huawei eSpace IAD Скачать руководство пользователя страница 41

Страница: 41 / 109

eSpace IAD
Troubleshooting

2 Analy zing and Rectify ing Faults

Issue 02 (2012-02-29)

Huawei Proprietary and Confidential

Table 2-3

Fax/Modem service performance and network quality

Service Type

Performance

in a Good
Network

Performance

in a Poor
Network

Performance

in a Bad
Network

Modem

Transfer

Proved

Failed

Fax

Transfer

Proved

Failed

For example:

−

If SIP is used, run the

sip send-capability fax pri

command to set the faxing mode to

T.38.

TERMINAL(advanced-config)#

sip send-capability fax pri 0 t38 redundancy 2

If the fax encoding/decoding priority configuration fails, run the

display sip send-capability

command

to view the configuration result, and find out the priority for the required encoding/decoding type. Run
the

undo sip send-capability fax pri

command to delete the priority, and run the

sip send-capability

fax pri

command to set the priority again.

−

If MGCP is used, run the

mgcp soft-parameter

command to set the faxing mode to

t38v2.

TERMINAL(advanced-config)#

mgcp soft-parameter fax-mode t38v2



If the network quality is good, go to

Step 6

Step 6

Capture IAD network packets to verify that both ends of media negotiation use the same
codec. If downspeeding is performed, check whether downspeeding is successful.



If no, the network quality is poor.



If yes, go to

Step 8

Step 7

Check whether the packet consists of the following parameters:



a=T38FaxFillBitRemoval:0



a=T38FaxTranscodingMMR:0



a=T38FaxTranscodingJBIG:0



a=T38FaxUdpEC:t38UDPRedundancy

These parameters are not supported by the IAD.

Step 8

Check whether echo exists in the voice sent from the core network.



If yes, contact the core network management personnel to find out the time when the
echo is generated.



If no, go to

Step 9

Step 9

Contact Huawei technical support.

----End

Содержание eSpace IAD














































































































Результаты поиска

Содержание eSpace IAD

Отзывы:

Похожие инструкции для eSpace IAD

Бренды по названию

Популярные бренды

Huawei eSpace IAD, Руководство по устранению неисправностей

Результаты поиска

Содержание eSpace IAD

Отзывы:

Похожие инструкции для eSpace IAD

Бренды по названию

Популярные бренды