Huawei eSpace IAD Скачать руководство пользователя страница 74 | Manualshive

Страница: 74 / 109

background image

eSpace IAD
Troubleshooting

3 Co mmon Troubleshooting Methods

Issue 02 (2012-02-29)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

69

Figure 3-1

Call failure records

You can click

Download

to download call failure records, or enter a user number to view the

call failure records of a specified user.

When the IAD is connected to the SoftSwitch, the user number is the same as

DN

on the SoftSwitch.

CLI Mode

Run the

display sip calloutrecords

command to view the call failure records. For example:

TERMINAL(config)#

display sip calloutrecords pstnport 4

portnum   callernum        calleenum         startTime            endTime
onhookSide  hookReasonType
-----------------------------------------------------------------------------------
-----------------------------------------------
4        81011             81009           2005-01-01 00:18:55  2005-01-01 00:19:27  remote
the  request is timeout  from client

-----------------------------------------------------------------------------------
-----------------------------------------------
TERMINAL(config)#

display sip calloutrecords slot 1 pstnport 2

3.4 Checking the Network Status Automatically

By using this function, you can check the connection between an IAD and a specified device.
If enable the function, the IAD generates the alarm information when the network connection
is interrupted or restored. You can locate the faults according to the alarm information.

Application Instance

Network Requirements

The IAD is connected to the SIP server through LAN. The IP address of SIP server is
192.163.1.8. Problem description: The registered SIP users become unregistered.

The troubleshooting method is as follows:



«
...
72
73
74
75
76
...
»

Содержание eSpace IAD














































































































Отзывы:

Нет отзывов

Похожие инструкции для eSpace IAD

Бренд: D-Link Страницы: 6

Бренд: iDance Страницы: 10

Бренд: Blaupunkt Страницы: 15

TesiraFORTÉ AVB VT4

Бренд: Biamp Страницы: 2

Бренд: Goodmans Страницы: 22

Бренд: Caliber Страницы: 20

VC210 Teams Edition

Бренд: Yealink Страницы: 32

Бренд: ASA Electronics Страницы: 2

Бренд: Sonetics Страницы: 8

VideoJet 400 19"

Бренд: VCS Страницы: 86

Бренд: Akai Страницы: 6

Бренд: Jazz Страницы: 12

Бренд: Cisco Страницы: 4

Бренд: E-Bench Страницы: 22

Бренд: RCA Страницы: 18

Бренд: Welton USA Страницы: 2

Бренд: THOMSON Страницы: 68

Бренд: Reliance Foundry Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды