Huawei eSpace IAD Скачать руководство пользователя страница 38

Страница: 38 / 109

eSpace IAD
Troubleshooting

2 Analy zing and Rectify ing Faults

Issue 02 (2012-02-29)

Huawei Proprietary and Confidential

Select a package from the

IPFAX

drop-down list box, and add the package.

Step 5

Run the

#mgcp soft-parameter fax-mode 711v2 mgc-type zte

command to configure the

faxing mode on the IAD.

Step 6

If the fault persists after you perform the preceding operations, contact Huawei technical
support.

----End

2.2.3 Fax Machines Connected to the Counter Work Improperly

Symptom

Network:

Softswitch-IAD-Counter-Fax machine

A fax machine connected to the IAD through the counter cannot receive or send faxes
properly.

Cause

The possible causes are as follows:



Poor bearer network performance



Inconsistent faxing modes



Incorrect softswitch type



Cable loss

Solution

Step 1

Ping the softswitch IP address to check the delay time and packet loss.



If the delay time is too long and packet loss occurs, the bearer network performance is
poor. Verify the network connection.



If the network is normal, go to

Step 2

Step 2

Check the consistency between the faxing modes of the softswitch and IAD.

Consult related personnel about the method for viewing the softswitch faxing mode.

To view the IAD faxing mode, proceed as follows:

Run the

display protocol-mode

command to view the protocol used by the IAD.

If MGCP is used, run the

display mgcp soft-parameter

command to view the faxing

mode. If the faxing mode is different from that of the softswitch, run the

mgcp

soft-parameter fax-mode

command to change the faxing mode. If the faxing modes are

the same, go to

Step 3

If SIP is used, run the

display sip send-capability

command to view the faxing mode. If

the faxing mode is different from that of the softswitch, run the

sip send-capability fax

pri

command to change the faxing mode. If the faxing modes are the same, go to

Step 3

Step 3

Check the softswitch manufacturer and the softswitch type of the IAD.

Run the

display protocol-mode

command to view the protocol used by the IAD.

Содержание eSpace IAD














































































































Результаты поиска

Содержание eSpace IAD

Отзывы:

Похожие инструкции для eSpace IAD

Бренды по названию

Популярные бренды

Huawei eSpace IAD, Руководство по устранению неисправностей

Результаты поиска

Содержание eSpace IAD

Отзывы:

Похожие инструкции для eSpace IAD

Бренды по названию

Популярные бренды