Huawei eSpace IAD Скачать руководство пользователя страница 102

Страница: 102 / 109

eSpace IAD
Troubleshooting

3 Co mmon Troubleshooting Methods

Issue 02 (2012-02-29)

Huawei Proprietary and Confidential

Figure 3-26

Connection diagram for testing impedance greater than or equal to 1 ohm

Figure 3-27

shows the connection diagram for testing impedance less than 1 ohm (both

conductors on points E are connected to the ground electrode).

Figure 3-27

Connection diagram for testing impedance less than 1 ohm

Test Procedure

Ensure that the connections between the tester, ground electrode, and probes are correct.

Place the tester horizontally and ensure that the pointer is on the central line.

Set the ratio scale to the maximum, rotate the electric generator handle slowly, and move
the tester until the pointer is on the central line.

When the pointer becomes stable on the central line, rotate the electric generator quickly
(more than 150 rounds per minute), and move the tester until the pointer is on the central
line again.

If the reading is less than 1, change the ratio scale to a smaller one and perform the test
again.

If the pointer shakes, change the handle rotating speed until the pointer becomes stable.

Precautions



Place and take the tester carefully and avoid severe shake.



The ground conductor must be disconnected from devices.

Содержание eSpace IAD














































































































Результаты поиска

Содержание eSpace IAD

Отзывы:

Похожие инструкции для eSpace IAD

Бренды по названию

Популярные бренды

Huawei eSpace IAD, Руководство по устранению неисправностей

Результаты поиска

Содержание eSpace IAD

Отзывы:

Похожие инструкции для eSpace IAD

Бренды по названию

Популярные бренды