Huawei eSpace IAD Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 109

background image

eSpace IAD
Troubleshooting

2 Analy zing and Rectify ing Faults

Issue 02 (2012-02-29)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

42

2.3.5 PPPoE Dialing Failure

Symptom

When you obtain IP address through Point-to-Point Protocol over Ethernet (PPPoE), the
dialing fails.

Cause

The failure may be caused by network disconnection, invalid user name or password, or false
login information after a fault occurs and the PPPoE server restarts.

Solution

1.

Check whether the network is disconnected. For details, see

2.3.3 Network Connection

2.

Run the

display ipaddress

command to view the IP address obtaining mode. Ensure that

the PPPoE mode is adopted.

TERMINAL>

display ipaddress

--------------------------------------------------
DNS Domain Name...............: tele.com
Physical Address..............: 00-e0-fc-a8-d0-0d /*

MAC address

*/

IP Address Get Method.........: Static IP config /*

Obtaining method of IP address

*/

...

The preceding information indicates that the IP address obtaining mode is static IP
address. Run the

ipaddress pppoe

command in the global configuration mode to enable

the PPPoE dialing mode, and then run the

pppoe

user name

password

password

command

to set the user name and password.

3.

Run the following command to check whether the PPPoE is online. If the PPPoE is
offline, check the correctness of the user name and password.

TERMINAL(config)#

display ipaddress

--------------------------------------------------
  DNS Domain Name...............:
  Physical Address..............: 00-e0-fc-3e-57-2d
  IP Address Get Method.........: PPPoE
  cpm (unit number 0):
    Flags: (0x400) DOWN TRAILERS ARP
    IP Address..................: 192.166.1.102
    Subnet Mask.................: 255.255.255.0
    Default Gateway.............: 192.166.1.1
  Destination IP Address........:
  PPPoE Dialup on System Start..: yes
  PPPoE Online..................: yes /*

yes indicates that the PPPoE is online.

*/

  PPPoE Dialup Username.........: hHuawei
  PPPoE Dialup Password.........: ******
--------------------------------------------------

4.

If the IAD is reset by accident or restarted because the power is off, the users may still be
in  online  state  in  the PPPoE server. If  you  try  to  dial  a  number  before  the  account  times
out  and  drops  offline,  the  dial  fails.  You  can  wait  for  a  few  minutes  before  redial  the
number.

«
...
45
46
47
48
49
...
»

Содержание eSpace IAD














































































































Отзывы:

Нет отзывов

Похожие инструкции для eSpace IAD

Бренд: R.V.R. Elettronica Страницы: 38

Бренд: Garmin Страницы: 10

Бренд: JAMO Страницы: 8

Бренд: Tokai Страницы: 20

Бренд: Aiwa Страницы: 20

Бренд: CLIMAVENETA Страницы: 23

Бренд: Nolan Страницы: 48

Бренд: Avaya Страницы: 5

Бренд: Hama Страницы: 53

Бренд: babala Страницы: 30

Countryman Type 10S Stereo Direct Box

Бренд: CAI Страницы: 16

C7301U - Cd Rcvr W/ Custm Dsply

Бренд: Panasonic Страницы: 66

Бренд: Kenwood Страницы: 17

Бренд: Kenwood Страницы: 2

Бренд: Kenwood Страницы: 12

Бренд: Kenwood Страницы: 68

Бренд: Kenwood Страницы: 28

Бренд: Kenwood Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды