Huawei eSpace IAD Скачать руководство пользователя страница 84

Страница: 84 / 109

eSpace IAD
Troubleshooting

3 Co mmon Troubleshooting Methods

Issue 02 (2012-02-29)

Huawei Proprietary and Confidential

Table 3-2

Command description

Item

Description

Value Range

IAD208E(
M)

IAD132E
(T)

IAD1224

source-port

Source mirror
port. Configure
the uplink
network port of
the IAD as the
source mirror
port.

1 to 8

1 to 4

1 or 2

destination-
port

Destination
mirror port.
Configure the
port that is
connected to the
IAD on the PC
as the
destination
mirror port.

1 to 8

1 to 4

1 or 2

CAUTION

The uplink port of the IAD
which is used to connect the
IAD to the superior devices and
the port which is used for
cascading connections cannot
be set as the destination
mirrored port.

Capturing packets by using the mirror port on the switch

Connect the PC and the IAD to the same switch. The networking scheme is shown in

Figure

3-11

Figure 3-11

Networking example 3

Содержание eSpace IAD














































































































Результаты поиска

Содержание eSpace IAD

Отзывы:

Похожие инструкции для eSpace IAD

Бренды по названию

Популярные бренды

Huawei eSpace IAD, Руководство по устранению неисправностей

Результаты поиска

Содержание eSpace IAD

Отзывы:

Похожие инструкции для eSpace IAD

Бренды по названию

Популярные бренды