Huawei eSpace IAD Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 109

background image

eSpace IAD
Troubleshooting

2 Analy zing and Rectify ing Faults

Issue 02 (2012-02-29)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

57

Solution

1.

Check whether the scroll lock on the keyboard is on, which prevents the automatic scroll
of the command line interface (CLI).

2.

Check the connection of the serial cable and the check the serial port number. You can
switch the serial ports.

3.

If illegible characters are generated but commands cannot be entered, the fault may be
caused by incorrect serial port parameter configuration. Set

Baud Rate

to

9600

,

data

bits

to

8

,

stop bits

to

0

, and

authentication

to

null

.

4.

If the RUN indicator is not blinking, the IAD is down. For details, see

Device Indicators

. Press the Reset button to restart the device (do not turn off the power

or the previously stored alarm records will be lost), and view and analyze the alarms.

5.

(Optional) You can try to log in to the IAD through Telnet.

2.3.24 Start Slowness or Failure

Symptom

The start process is slow or stopped. No response is generated for inputs from the keyboard
and the system does not automatically restart.

Cause

The possible causes are as follows:



If the IAD uses the DHCP to automatically obtain the IP address, the fault may be caused
because the IP addresses in the network are not sufficient for allocation and the waiting
queue is too long.



When domain name is used for registration to the UCEMS, if the DNS does not exist or
has incorrect configuration, the domain name parse will fail and the system will wait for
a long time.



If it is set that the IAD upgrades through the FTP/TFTP server and the configuration of
the IP address of the FTP/TFTP server is incorrect, the file request will wait for some
time because no response message is received.



System errors.

Solution

1.

If the method for obtaining the IP address of the IAD is DHCP, run the

ipaddress static

command to set a fixed IP address, and then run the

reboot

command to restart the

system. Check whether exceptions occur.

2.

Run the

display nms

command to view the nms status.

TERMINAL#

display nms

the config is DNS /*

DNS indicates that the IAD is registered to the network

management platform through DNS.

*/

domainName /*

Domain name

*/

  iadms.com
get community   : ********
set community   : ********
trap community  : ********
trap port       : 162
nms access value: Disable

«
...
60
61
62
63
64
...
»

Содержание eSpace IAD














































































































Отзывы:

Нет отзывов

Похожие инструкции для eSpace IAD

Бренд: Zenith Страницы: 24

MDS TransNEXT NET9L

Бренд: GE Страницы: 69

Бренд: auna multimedia Страницы: 124

Бренд: Quickie Страницы: 108

DuplicAir Intelligent Control Blue

Бренд: Jydepejsen Страницы: 52

SoundPoint IP 320

Бренд: Polycom Страницы: 2

Бренд: T-audio Страницы: 2

Бренд: Saltillo Страницы: 2

Бренд: Technics Страницы: 14

AMETEK ORBIT ACS Series

Бренд: Solartron Metrology Страницы: 63

Бренд: CDK ELECTRONICS Страницы: 22

Stealthbox SB-D-DRNGO/10W0

Бренд: JL Audio Страницы: 3

Бренд: Spracht Страницы: 24

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 112

Бренд: Contacta Страницы: 12

Бренд: Sony Страницы: 2

XT-XM1 - Xm Satellite Radio Tuner

Бренд: Sony Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды