Huawei eSpace IAD Скачать руководство пользователя страница 36

Страница: 36 / 109

eSpace IAD
Troubleshooting

2 Analy zing and Rectify ing Faults

Issue 02 (2012-02-29)

Huawei Proprietary and Confidential

Solution

Step 1

Check whether the IP addresses configured for MG domain names are the same on the
softswitch.



If the IP addresses are the same, modify the configuration.



If the IP addresses are different, go to

Step 2

Step 2

Capture packets to check whether the signaling delivered by the softswitch is normal.



If the signaling is normal, go to

Step 3



If the signaling is abnormal, check the softswitch.

Step 3

Contact Huawei technical support engineers.

----End

2.2 Fax and Modem Faults

2.2.1 Faxes Can Be Received but Cannot Be Sent

Symptom

A fax machine connected to the IAD can receive but cannot send faxes.

Cause

The possible causes are as follows:



Poor bearer network performance



Inconsistent faxing modes



Incorrect softswitch type

Solution

Step 1

Ping the softswitch IP address to check the delay time and packet loss.



If the delay time is too long and packet loss occurs, the bearer network performance is
poor. Verify the network connection.



If the network is normal, go to

Step 2

Step 2

Check the consistency between the faxing modes of the softswitch and IAD.

Consult related personnel about the method for viewing the softswitch faxing mode.

To view the IAD faxing mode, proceed as follows:

Run the

display protocol-mode

command to view the protocol used by the IAD.

If MGCP is used, run the

display mgcp soft-parameter

command to view the faxing

mode. If the faxing mode is different from that of the softswitch, run the

mgcp

soft-parameter fax-mode

command to change the faxing mode. If the faxing modes are

the same, go to

Step 3

Содержание eSpace IAD














































































































Результаты поиска

Содержание eSpace IAD

Отзывы:

Похожие инструкции для eSpace IAD

Бренды по названию

Популярные бренды

Huawei eSpace IAD, Руководство по устранению неисправностей

Результаты поиска

Содержание eSpace IAD

Отзывы:

Похожие инструкции для eSpace IAD

Бренды по названию

Популярные бренды