Huawei eSpace IAD Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 109

background image

eSpace IAD
Troubleshooting

2 Analy zing and Rectify ing Faults

Issue 02 (2012-02-29)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

32

3.

If SIP is used, run the

display sip send-capability

command to view the faxing mode. If

the faxing mode is different from that of the softswitch, run the

sip send-capability fax

pri

command to change the faxing mode. If the faxing modes are the same, go to

Step 3

Check the softswitch manufacturer and the softswitch type of the IAD.

The softswitch type configured on the IAD must be the same as the actual softswitch type.

1.

Run the

display protocol-mode

command to view the protocol used by the IAD.

2.

If MGCP is used, run the

display mgcp soft-parameter

command to view the

softswitch type of the IAD. If the softswitch type of the IAD is different from the actual
softswitch type, run the

mgcp soft-parameter mgc-type

command to change the

softswitch type. If the softswitch types are the same, go to

3.

If SIP is used, run the

display sip soft-parameter

command to view the softswitch type

of the IAD. If the softswitch type of the IAD is different from the actual softswitch type,
run the

sip soft-parameter soft-switch-type

command to change the softswitch type. If

the softswitch types are the same, go to

Step 4

Contact Huawei technical support.

----End

2.2.2 IAD Fails to Send Faxes to ZTE Softswitches

Symptom

In the MGCP mode, the IAD fails to send faxes to ZTE ZS SS10.

Cause

By default, the T30 mode is configured on ZTE softswitches for ZTE IADs that use the H248
protocol. When Huawei IADs send or receive faxes using MGCP, the softswitch cannot
recognize all information and the faxing fails.

Proprietary protocols are used to send heartbeat messages for devices of all manufacturers,
and therefore 522 message will be displayed. This error does not affect communication.

Solution

Step 1

Configure a static attribute template, default attribute template, and packet template when
adding an IAD.

Step 2

Modify the static attribute template.

When the fax service is enabled, MGCP faxing modes T30, T38, and T30 or T38 are
displayed on the static attribute template.

Select T30.

Step 3

Modify the default attribute template.

In the SDP description, select

Fax

, and change the codec mode and packaging duration to

PCMA

and

20

respectively. If the default value is used, 510 error occurs in the faxing

process.

Step 4

Modify the package template.

«
...
35
36
37
38
39
...
»

Содержание eSpace IAD














































































































Отзывы:

Нет отзывов

Похожие инструкции для eSpace IAD

Бренд: N-Com Страницы: 20

Бренд: N-Com Страницы: 28

Бренд: Panasonic Страницы: 16

Soundgear Series

Бренд: JBL Страницы: 73

Бренд: Polycom Страницы: 2

Бренд: Grandstream Networks Страницы: 27

Бренд: RAM Страницы: 22

Triton Barrier TL-2

Бренд: VALTIR Страницы: 28

Бренд: SONIQ Страницы: 7

Бренд: Redback Страницы: 16

Бренд: Hyundai Страницы: 61

Бренд: Boss Audio Systems Страницы: 6

Бренд: Boss Audio Systems Страницы: 25

Бренд: JVC Страницы: 88

Бренд: JVC Страницы: 14

Бренд: Cirrus Logic Страницы: 88

Бренд: RCA Страницы: 19

Бренд: Velux Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды