Huawei 3900 Series Скачать руководство пользователя страница 147 | Manualshive

Страница: 147 / 196

background image

7.1 Procedure for Commissioning the MBTS Using Local
Maintenance Terminal and M2000

At the local end of the MBTS, you can use local maintenance terminal to upgrade MBTS software
and configure MBTS data and to facilitate the establishment of MBTS OM at the MBTS. You
can also check whether the MBTS hardware status is normal according to the board status and
LED status, to locate and rectify faults (if any) in time. At the M2000, you can check the MBTS
operating status.

Prerequisite

Before you commission the MBTS, the MBTS, RNC, and M2000 must meet following
requirements:

l

The MBTS hardware such as the cabinets, cables, antenna system, and auxiliary devices,
is installed and passes the installation check. The MBTS is powered on and passes the
power-on check.

l

The controller hardware is installed and commissioned, and the system works properly.
The negotiation data of the MBTS to be commissioned is configured and recorded.

l

The M2000 is commissioned, it is connected to the corresponding controller, and the
configuration synchronization is completed.

In addition, the following requirements must be met:

l

A portable computer used for local commissioning is ready.

l

The portable computer is installed with local maintenance terminal mapping with the mode
of the base station to be commissioned.

l

The target version software package and data configuration file of the base station to be
commissioned are ready and saved on the portable computer.

Commissioning Flowchart

shows the procedure for commissioning the MBTS using local maintenance terminal

and M2000.

3900 Series Multi-Mode Base Station
Commissioning Guide

7 Commissioning the MBTS by Using Local Maintenance

Terminal and M2000

Issue 02 (2010-07-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

7-3

«
...
145
146
147
148
149
...
»

Содержание 3900 Series





































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3900 Series

Бренд: Acer Страницы: 2

Бренд: Acer Страницы: 4

Бренд: Kargo Master Страницы: 5

Бренд: Kappa Страницы: 4

Бренд: A-Tach Mounts Страницы: 2

Бренд: X-lite Страницы: 6

Бренд: V-TAC Страницы: 4

Бренд: Conrad Electronic Страницы: 24

Бренд: dol sensors Страницы: 4

PECOS Universal

Бренд: Speed Link Страницы: 4

Бренд: Mountain Top Страницы: 12

Бренд: Textron Страницы: 8

PowerBlade PBH-1540

Бренд: Swisher Страницы: 2

Бренд: R&G Страницы: 13

Бренд: Naish Страницы: 23

FIX&GO automatic

Бренд: Alfa Romeo Страницы: 40

Бренд: Park Tool Страницы: 2

Бренд: Nav TV Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды