Huawei 3900 Series Скачать руководство пользователя страница 115 | Manualshive

Страница: 115 / 196

background image

Parameter

Description

RNC Name

Name of the RNC to which the NodeB belongs
This parameter can be optionally exported from the CME. It is not
configurable in the

NodeB Auto Deployment

window.

NodeB ID

ID of the NodeB
This parameter must be exported from the CME. It is not configurable
in the

NodeB Auto Deployment

window.

NodeB Name

Name of the NodeB
This parameter must be exported from the CME. It is not configurable
in the

NodeB Auto Deployment

window.

NodeB ESN1

Electronic serial number (ESN) of the active main control board of a
NodeB (it must be exported from the CME if it is planned)
The ESN uniquely identifies one NodeB. The ESN is usually labeled
as the bar code on the main control board of the NodeB. The site
engineer should record the ESN before leaving the site, so as to assist
the commissioning engineer in the remote check on the site.
This parameter can be optionally exported from the CME. It is
configurable in the

NodeB Auto Deployment

window.

NodeB ESN2

ESN of the standby main control board of the NodeB (it must be
exported from the CME if it is planned)
This parameter can be optionally exported from the CME. It is
configurable in the

NodeB Auto Deployment

window.

NodeB TRANS IP
address

OM IP address of the NodeB configured at the RNC
This parameter must be exported from the CME. It is not configurable
in the

NodeB Auto Deployment

window.

NodeB TRANS IP
Subnet mask

OM IP subnet mask of the NodeB configured at the RNC
This parameter must be exported from the CME. It is not configurable
in the

NodeB Auto Deployment

window.

NodeB Interface IP
address

IP address of the port on the NodeB configured at the RNC (it must
be exported from the CME if the port type of the NodeB is set to ETH/
TRUNK)
This parameter can be optionally exported from the CME. It is not
configurable in the

NodeB Auto Deployment

window.

NodeB Interface IP
Subnet mask

IP subnet mask of the port on the NodeB configured at the RNC (it
must be exported from the CME if the port type of the NodeB is set
to ETH/TRUNK)
This parameter can be optionally exported from the CME. It is not
configurable in the

NodeB Auto Deployment

window.

3900 Series Multi-Mode Base Station
Commissioning Guide

5 Commissioning the MBTS in GL or UL Mode on the

M2000

Issue 02 (2010-07-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

5-55

«
...
113
114
115
116
117
...
»

Содержание 3900 Series





































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3900 Series

Бренд: Samsung Страницы: 133

CSL Elite Racing Wheel

Бренд: FANATEC Страницы: 2

Бренд: FANATEC Страницы: 8

Бренд: FANATEC Страницы: 35

Бренд: Garmin Страницы: 22

Бренд: Sami Страницы: 10

Бренд: QIMMIQ Страницы: 16

Бренд: QA1 Страницы: 10

Бренд: daviteq Страницы: 33

Бренд: Trace2O Страницы: 9

Care@Home MDsense

Бренд: Essence Smartcare Страницы: 12

5TH GEN 4RUNNER

Бренд: Victory 4x4 Страницы: 5

Бренд: Keith Страницы: 2

Бренд: Mystic Romance Страницы: 10

Бренд: Antec Страницы: 8

Бренд: Banner Страницы: 22

Бренд: Land Pride Страницы: 10

Бренд: Hank Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды