Huawei 3900 Series Скачать руководство пользователя страница 142

Страница: 142 / 196

If the CPRI LED Is...

It Indicates That...

Then...

OFF

The port of the optical
module is not configured,
the optical module is
powered off, or the LED is
faulty.

If the MRFU or RRU3908
is connected to this port,
check the installation of
BBU and RRU according to
configuration
requirements.

If the installation is
inconsistent with
configuration
requirements, reinstall
the RRU according to
configuration
requirements.

If the installation is
consistent with
configuration
requirements, replace
the boards.

ON (red)

The port of optical module
is configured, but the
optical module is not in
position, or the CPRI
optical cable is improperly
connected.

Handle the alarm according
to the suggestions. For
details, see

Alarm

Reference

Blinking red, ON for 1s,
OFF for 1s)

The RRU or LRFU on the
CPRI link reports the
VSWR alarm.

Handle the alarm according
to the suggestions. For
details, see

Alarm

Reference

Blinking (red, ON for
0.25s, OFF for 0.25s)

The RRU or LRFU on the
CPRI link is faulty.

Handle the alarm according
to the suggestions. For
details, see

Alarm

Reference

Step 2

Check the ALM LEDs on the PMU/AFMU/EMUA.

If the ALM LED Is... It Indicates That...

Then...

OFF

The module or the
device is functioning
properly.

The check is complete.

The module or the
device is faulty.

Reinstall the module or power on the
device again to check whether the fault is
rectified.

Step 3

Check the VSWR LED status of the MRFU/RRU3908, and perform the next step based on the
status of the VSWR LED.

6 Commissioning the MBTS by Using USB and M2000

3900 Series Multi-Mode Base Station

Commissioning Guide

6-24

Huawei Proprietary and Confidential

Issue 02 (2010-07-30)

Содержание 3900 Series





































































































































































































Результаты поиска

Содержание 3900 Series

Отзывы:

Похожие инструкции для 3900 Series

Бренды по названию

Популярные бренды

Huawei 3900 Series, Руководство по вводу в эксплуатацию

Результаты поиска

Содержание 3900 Series

Отзывы:

Похожие инструкции для 3900 Series

Бренды по названию

Популярные бренды