Huawei 3900 Series Скачать руководство пользователя страница 173 | Manualshive

Страница: 173 / 196

background image

Prerequisite

l

The BBU is properly connected to the BSC through an E1/T1 cable.

l

The BBU and the BSC are successfully powered on.

Procedure

Step 1

Check whether the UTRP is installed. If it is installed, perform the check based on the following
table. If it is not installed, go to

.

If ...

Then ...

The RUN LED is oN for 1s and off for 1s
and the ALM LED is off.

The board properly works according to the
configuration. Then, go to

.

The RUN LED is on for 0.125s and off
for 0.125s.

The board is not configured or software is being
loaded to the board. After the board is configured
or the loading is complete, go to

The RUN and ALM LED are in other
states.

The E1/T1 link is faulty. Go to

Step 2

Check whether the settings of DIP switch meet the field requirements. if not, modify the settings
of DIP switch as required.

Step 3

Check the status of the LEDs

LIU0

to

LIU3

on the panel of the GTMU in the BBU. The LEDs

LIU0

to

LIU3

correspond to links 1 to 4 of the E1/T1 cable respectively. Each link has one TX

line and one RX line.

If ...

Then ...

The LED is OFF

The E1/T1 link is normal. End this task.

The LED is on or on for 0.125s and off for 0.125s.

The E1/T1 link is faulty. Go to

NOTE

You need to check the status of only the

LIU

LED corresponding to the E1/T1 link in use. The

LIU

LEDs

corresponding to the unused E1/T1 links are on.

l

For the BBUs that are not connected in cascading mode, if the LIU LED for the E1/T1 link is off, the
communication between the BBU and the BSC is normal. If the LIU LED is on, the communication
is abnormal.

l

For the BBUs that are connected in cascading mode, if the LIU LEDs on the E1 ports corresponding
to level 1 BBU and level 2 BBU are off, the communication is normal. If multiple BBUs are connected
in cascading mode, check the LEDs of the corresponding links.

l

If the BBU and the BSC form a ring, check the LIU LEDs corresponding to the links in the ring. To
check the inter-BBU connections, check the corresponding LEDs of the cascaded BBUs.

Step 4

Check the connections and connectors at both ends of the cables. If a connector is damaged,
replace it.

3900 Series Multi-Mode Base Station
Commissioning Guide

7 Commissioning the MBTS by Using Local Maintenance

Terminal and M2000

Issue 02 (2010-07-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

7-29

«
...
171
172
173
174
175
...
»

Содержание 3900 Series





































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3900 Series

CRD 2 00-1000S Series

Бренд: Symbol Страницы: 16

Бренд: Canon Страницы: 10

Бренд: BAC Страницы: 36

Бренд: Baader Planetarium Страницы: 6

Бренд: T&C Страницы: 16

7400DN - Phaser Color LED Printer

Бренд: Xerox Страницы: 3

WorkCentre Pro 123

Бренд: Xerox Страницы: 4

Бренд: Harol Страницы: 17

Бренд: Cab Technology Страницы: 10

Бренд: Kelvion Страницы: 30

Бренд: Magnus Страницы: 6

Бренд: aquatherm Страницы: 32

Бренд: Metz Страницы: 112

Бренд: FORM FIT Страницы: 2

Edge Flush Rail

Бренд: Thule Страницы: 12

Бренд: Cateye Страницы: 2

UE-12Li100BL IN Series

Бренд: UPOWER Ecoline Страницы: 2

Бренд: BAFANG Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды