manualshive.com logo in svg

horiba HT-110, Инструкция по эксплуатации, Страница: 52 / 57

Поделиться
Скачать
horiba HT-110 Скачать руководство пользователя страница 52

7 Reference Materials

44

7

Reference Materials

7.1

Specifications

Product name

Total Organic Carbon Analyzer

Model

HT-110

Measurement method

Continuous UV oxidation conductivity method

Measurement limit

0 ppb to 1000 ppb

Measurement range

0 ppb to 100/500/1000 ppb

Repeatability

Within ±2% of full scale

Display resolution

0.1 ppb (0 ppb to 100 ppb / 0 ppb to 500 ppb range)
1 ppb (0 ppb to 1000 ppb range)

Transmittance output

Number of output point : one
4 mA to 20 mA DC  / 0 V to 1 V DC (optional) insulated input/output
Maximum load resistance: 600 

Ω

 (minimum load resistance 100 kW  (when 

optionally selected)
Transmittance output range: optional setting possible within measurement range
Output target: TOC concentration

Contact output

Number of outputs: two
Alarm contact output (RLY1)
Contact method: relay contact, SPDT (1c)
Contact capacity:125 V 3 A AC / 24 V 3 A DC (load resistance)
Contact function: upper/lower limit function (ON/OFF control)
Output target: 
 at TOC, temperature, conductivity:
    C-NO contact is "closed" during operation, "open" during normal  conditions 
   (including a POWER OFF state) *C-NO contact is reversed
 at hold, or error:
    C-NO contact is "open" during operation (including a POWER OFF state), 
    "closed" during normal conditions   *C-NO contact is reversed
Alarm contact output (RLY2)
Contact method: relay contact, SPST (1a)
Contact capacity: 125 V 3 A AC / 24 V 3 A DC (load resistance)
Contact function: upper/lower limit function (ON/OFF control)
Output target: TOC concentration

Contact input

Number of input point: one
Non-voltage normal open (1a) signal input (open collector input possible)
Insulation-type input
Max. ON resistance: 50 

Ω

Open-circuit voltage: 5 V DC
Max. short circuit current: 10 mA
An error will not be generated even if there is notification of no sample detection 
immediately after receipt of the pure water device stop signal receiving
The hold operation during the contact input receiving

Sample water condition

Conductivity: less than 10 µS/cm (less than 2 µS/cm in 0 to 100 ppb range)
Temperature: 5

°

C to 99

°

C

Pressure: 0.03 MPa to 0.50 MPa, 
Pressure fluctuation: within ±0.05 MPa (within the specified pressure range)
Flow rate: 20 mL/min to 200 mL/min

Environmental conditions

Temperature: 5

°

C to 40

°

C

Relative humidity: less than 85%

Содержание HT-110


























































Отзывы:

Нет отзывов