horiba HT-110 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 57

horiba HT-110 Скачать руководство пользователя страница 2

February, 2009 © 2008

−

2009 HORIBA Advanced Techno, Co., Ltd.

Preface

This manual describes the operation of the Total Organic Carbon Analyzer, HT-110.
Be sure to read this manual before using the product to ensure proper and safe operation of
the instrument. Also safely store the manual so it is readily available whenever necessary.

Product specifications and appearance, as well as the contents of this manual are subject to
change without notice.

■

Warranty and Responsibility

HORIBA ADVANCED TECHNO warrants that the Product shall be free from defects in
material and workmanship and agrees to repair or replace free of charge, at HORIBA
ADVANCED TECHNO’s option, any malfunctioned or damaged Product attributable to
HORIBA ADVANCED TECHNO’s responsibility for a period of one (1) year from the delivery
unless otherwise agreed with a written agreement. In any one of the following cases, none of
the warranties set forth herein shall be extended;

z

Any malfunction or damage attributable to improper operation

z

Any malfunction attributable to repair or modification by any person not authorized by
HORIBA ADVANCED TECHNO

z

Any malfunction or damage attributable to the use in an environment not specified in this
manual

z

Any malfunction or damage attributable to violation of the instructions in this manual or
operations in the manner not specified in this manual

z

Any malfunction or damage attributable to any cause or causes beyond the reasonable
control of HORIBA ADVANCED TECHNO such as natural disasters

z

Any deterioration in appearance attributable to corrosion, rust, and so on

z

Replacement of consumables

HORIBA ADVANCED TECHNO SHALL NOT BE LIABLE FOR ANY DAMAGES RESULTING
FROM ANY MALFUNCTIONS OF THE PRODUCT, ANY ERASURE OF DATA, OR ANY
OTHER USES OF THE PRODUCT.

■

Trademarks

Generally, company names and brand names are either registered trademarks or trademarks
of the respective companies.

«
1
2
3
4
...
»

Содержание HT-110


























































Отзывы:

Нет отзывов