manualshive.com logo in svg

Honeywell AUTOMATIC CONTROL SI Edition, Инструкция по эксплуатации

"Инженерное руководство Honeywell AUTOMATIC CONTROL SI Edition теперь доступно для загрузки бесплатно на manualshive.com. Этот инновационный продукт обеспечивает автоматический контроль и управление, упрощая процессы. Скачайте руководство прямо сейчас и узнайте больше о возможностях этого устройства."

Поделиться
Скачать
background image

PNEUMATIC CONTROL FUNDAMENTALS

ENGINEERING MANUAL OF AUTOMATIC CONTROL

69

The oil coalescing filter continues to coalesce and drain off

accumulated oil until solid particles plug the filter. An increase
in pressure drop across the filter (to approximately 70 kPa)
indicates that the filter element needs replacement. For very
dirty air, a 0.005 millimeter prefilter filters out large particles
and increases the life of the final filter element.

PRESSURE REDUCING VALVES

A pressure reducing valve station can have a single-pressure

reducing valve or a two-pressure reducing valve, depending on
the requirements of the system it is supplying.

Single-Pressure Reducing Valve

After it passes though the filter, air enters the PRV (Fig. 11).

Inlet pressure ranges from 415 to 1035 kPa, depending on tank
pressures maintained by the compressor. Outlet pressure is
adjustable from 0 to 175 kPa, depending on the control air
requirements. The normal setting is 140 kPa.

A safety relief valve is built into some PRV assemblies to

protect control system devices if the PRV malfunctions. The
valve is typically set to relieve downstream pressures above
165 kPa.

Two-Pressure Reducing Valve

A two-pressure reducing valve is typically set to pass 90 or

124 kPa to the control system, as switched by a pilot pressure.
The two-pressure reducing valve is the same as the single-
pressure reducing valve with the addition of a switchover
diaphragm and switchover inlet to accept the switchover
pressure signal. Switchover to the higher setting occurs when
the inlet admits main air into the switchover chamber.
Exhausting the switchover chamber returns the valve to the
lower setting.

The switchover signal is typically provided by an E/P relay

or a two-position diverting switch. An automatic time clock
can operate an E/P relay to switch the main pressure for a
day/night control system. A diverting switch is often used to
manually switch a heating/cooling system.

In many applications requiring two-pressure reducing

valves, a single-pressure reducing valve is also required to
supply single-pressure controllers which do not perform well
at low pressures. Higher dual pressure systems operating at
140 and 170 kPa are sometimes used to eliminate the need
and expense of the second PRV.

THERMOSTATS

Thermostats are of four basic types:

— A low-capacity, single-temperature thermostat is the basic

nozzle-flapper bleed-type control described earlier. It is
a bleed, one-pipe, proportional thermostat that is either
direct or reverse acting.

— A high-capacity, single-temperature thermostat is a low-

capacity thermostat with a capacity amplifier added. It is
a pilot-bleed, two-pipe, proportioning thermostat that is
either direct or reverse acting.

— A dual-temperature thermostat typically provides

occupied/unoccupied control. It is essentially two
thermostats in one housing, each having its own bimetal
sensing element and setpoint adjustment. A valve unit
controlled by mainline pressure switches between the
occupied and unoccupied mode. A manual override lever
allows an occupant to change the thermostat operation
from unoccupied operation to occupied operation.

— A dual-acting (heating/cooling) thermostat is another

two-pipe, proportioning thermostat that has two bimetal
sensing elements. One element is direct acting for heating
control, and the other, reverse acting for cooling control.
Switchover is the same as for the dual-temperature
thermostat but without manual override.

Other thermostats are available for specific uses. Energy con-

servation thermostats limit setpoint adjustments to reasonable
minimums and maximums. Zero energy band thermostats
provide an adjustable deadband between heating and cooling
operations.

The thermostat provides a branchline air pressure that is a

function of the ambient temperature of the controlled space
and the setpoint and throttling range settings. The throttling
range setting and the setpoint determine the span and operating
range of the thermostat. The nozzle-flapper-bimetal assembly

Содержание AUTOMATIC CONTROL SI Edition

































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AUTOMATIC CONTROL SI Edition

Daikin Maverick I Operation Manual preview
Maverick I
Бренд: Daikin Страницы: 48
Daikin MicroTech III Operating Manual preview
MicroTech III
Бренд: Daikin Страницы: 77
Daikin MicroTech III Operation And Maintenance Manual preview
MicroTech III
Бренд: Daikin Страницы: 32
Daikin BRC1E71 Engineeiring Data preview
BRC1E71
Бренд: Daikin Страницы: 46
Daikin MicroTech III Installation And Maintenance Manual preview
MicroTech III
Бренд: Daikin Страницы: 14
Daikin DCS601C51 Hardware Manual preview
DCS601C51
Бренд: Daikin Страницы: 16
Daikin BRC944B2 Quick User Manual preview
BRC944B2
Бренд: Daikin Страницы: 1
Danfoss VLT AutomationDrive FC 302 Installation Manual preview
VLT AutomationDrive FC 302
Бренд: Danfoss Страницы: 128
Danfoss VLT DriveMotor FCP 106 Installation Instructions preview
VLT DriveMotor FCP 106
Бренд: Danfoss Страницы: 4
Harmonic Drive LA Series Manual preview
LA Series
Бренд: Harmonic Drive Страницы: 25
Nelson MR Technical Application Manual preview
MR
Бренд: Nelson Страницы: 8
Hach SC4200c User Manual preview
SC4200c
Бренд: Hach Страницы: 36
Hach 2100Q User Instructions preview
2100Q
Бренд: Hach Страницы: 72
Watts 2300 Series Installation Instructions Manual preview
2300 Series
Бренд: Watts Страницы: 12
Lancom GS-1108 Manual preview
GS-1108
Бренд: Lancom Страницы: 8
Nabco Opus Control Installation Manual preview
Opus Control
Бренд: Nabco Страницы: 35
Handicare SystemRoMedic EvaDrive450 Service Manual preview
SystemRoMedic EvaDrive450
Бренд: Handicare Страницы: 37
Simplex TrueAlarm 4100 Series Manual preview
TrueAlarm 4100 Series
Бренд: Simplex Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды