manualshive.com logo in svg

Honeywell AUTOMATIC CONTROL SI Edition, Инструкция по эксплуатации

"Инженерное руководство Honeywell AUTOMATIC CONTROL SI Edition теперь доступно для загрузки бесплатно на manualshive.com. Этот инновационный продукт обеспечивает автоматический контроль и управление, упрощая процессы. Скачайте руководство прямо сейчас и узнайте больше о возможностях этого устройства."

Поделиться
Скачать
background image

SMOKE MANAGEMENT FUNDAMENTALS

ENGINEERING MANUAL OF AUTOMATIC CONTROL

173

Smoke Management System, Active: A system that uses fans

to produce airflows and pressure differences across
smoke barriers to limit and direct smoke movement.

Smoke Management System, Passive: A system that shuts

down fans and closes dampers to limit the spread of
fire and smoke.

Smoke Control Zone: An indoor space enclosed by smoke

barriers, including the top and bottom, that is part of a
zoned smoke control system (NFPA 92A).

Smoke Damper: A device designed to resist the passage of air

or smoke that meets the requirements of UL 555S,
Standard for Leakage Rated Dampers for Use In
Smoke Control Systems.

Stack Effect: A movement of air or other gas in a vertical

enclosure induced by a difference in density between
the air or other gas in the enclosure and the ambient
atmosphere. The density difference is caused by
temperature-pressure differences between the air
inside a building and the air outside a building.  The
air inside the building moves upwards or downwards
depending on whether the air is warmer or colder,
respectively, than the air outside.

UL: Underwriter’s Laboratories Inc.

UPS: Uninterruptible Power Supply.

OBJECTIVES

Designing a smoke management system requires agreement

on the system objectives. The following is a partial list of
potential system objectives:

— Provide safety for the occupants
— Extend egress time
— Provide safe egress route

— Provide safe zones (tenable environment)
— Assist firefighters
— Limit property damage
— Limit spread of smoke away from fire area
— Clear smoke away for visibility
— Provide elevator usage during fires as an egress route

for the handicapped

DESIGN CONSIDERATIONS

GENERAL

Four points must be stressed in developing a smoke

management system:

1. The smoke management system can be properly designed

only with agreement on the objectives of the system.

2. The smoke management system must be designed as a

complete mechanical control system that is able to
function satisfactorily in the smoke management mode.
The smoke management system should be designed
independently of the HVAC system and then integrated,
where feasible, without sacrificing functionality of the
smoke control system.

3. The smoke management system must be designed to be

reliable, simple, and maintainable.

4. The smoke management system must be designed to

minimize the risks of failure and must be tested periodically.
Sensors providing status of operation and building
automation controls providing system monitoring and
printed records can assist in the testing process.

Present active smoke control systems use active methods and

follow two basic design approaches to preventing the movement
of smoke from the fire zone:

— Providing static pressure differences across penetrations

in smoke barriers, such as cracks around doors.

— Providing adequate velocity of air through large openings

in smoke barriers, such as doors in an open position.

Although these two methods are directly related, it is more

practical to use one or the other to design with and measure the
results.

Methods used to activate smoke control systems require

careful consideration. For zoned smoke control, care must be
taken in using smoke detectors to initiate a pressurization
strategy. If a smoke detector that is not in the smoke zone goes
into alarm, the wrong smoke control strategy will be employed.
If a pull station is activated from a nonsmoke zone, the wrong
smoke control strategy could again be employed.

Any alarm activation of a smoke management system that is

common to all strategies in the building, such as stairwell
pressurization, atria, and exhaust, is acceptable.

For a smoke management system to function reliably, building

leakage must be controlled during and after construction. Any
penetrations of smoke barriers and walls used for pressurization
must be carefully considered in order to maintain the intended
smoke control.

Содержание AUTOMATIC CONTROL SI Edition

































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AUTOMATIC CONTROL SI Edition

Sole Diesel SVT 10 Operator'S Manual preview
SVT 10
Бренд: Sole Diesel Страницы: 8
Eaton SC300 Operation Handbook preview
SC300
Бренд: Eaton Страницы: 166
Echelon Excel 50 Installation Instructions Manual preview
Excel 50
Бренд: Echelon Страницы: 40
Eaton PKE-COM-RTU Instruction Leaflet preview
PKE-COM-RTU
Бренд: Eaton Страницы: 2
Eaton i-on30R Installation Instructions preview
i-on30R
Бренд: Eaton Страницы: 2
Eaton MEMSHIELD 4 Installation Instructions Manual preview
MEMSHIELD 4
Бренд: Eaton Страницы: 8
Sakura Seiki Tissue-Tek TEC 6 Operating Manual preview
Tissue-Tek TEC 6
Бренд: Sakura Seiki Страницы: 6
RadioMaster MT12 Instruction Manual preview
MT12
Бренд: RadioMaster Страницы: 49
X10 SUPERREMOTE UR19A Addendum preview
SUPERREMOTE UR19A
Бренд: X10 Страницы: 3
Xantech MRC88M Installation Instructions Manual preview
MRC88M
Бренд: Xantech Страницы: 102
Xantech MRC88 Feature Descriptions preview
MRC88
Бренд: Xantech Страницы: 17
X10 CK11A Code List preview
CK11A
Бренд: X10 Страницы: 2
Invertek Optidrive Elevator Quick Start Up Manual preview
Optidrive Elevator
Бренд: Invertek Страницы: 5
Techtrol TLIC Instruction And Programming Manual preview
TLIC
Бренд: Techtrol Страницы: 4
Ros IC-15X Operation And Maintenance Manual preview
IC-15X
Бренд: Ros Страницы: 10
RAK WisBlock RAK19012 Quick Start Manual preview
WisBlock RAK19012
Бренд: RAK Страницы: 12
C.S.L. VARIVAC 2006 B Instruction & Installer'S Manual preview
VARIVAC 2006 B
Бренд: C.S.L. Страницы: 27
ICP DAS USA DS-700 Series Manual preview
DS-700 Series
Бренд: ICP DAS USA Страницы: 9

Бренды по названию

Популярные бренды

Загрузить еще бренды