Honeywell AlarmNet IGSMHS Скачать руководство пользователя страница 3

Страница: 3 / 64

Table of Contents

                                                

SECTION 1: General Information ........................................................................................................... 1-1

System Overview...................................................................................................................................... 1-1

Introduction ....................................................................................................................................... 1-1

General Information.......................................................................................................................... 1-1

System Features....................................................................................................................................... 1-2

About AlarmNet-i Internet Application ................................................................................................. 1-2

Encryption ................................................................................................................................................ 1-2

Modes of Operation .................................................................................................................................. 1-2

ECP Mode........................................................................................................................................... 1-2

Zone Trigger Mode............................................................................................................................. 1-3

4204 Mode and Two-4204 Mode ....................................................................................................... 1-3

Module Supervision Features.................................................................................................................. 1-3

Antenna.............................................................................................................................................. 1-4

Specifications............................................................................................................................................ 1-4

Mechanical ......................................................................................................................................... 1-4

Electrical ............................................................................................................................................ 1-4

RF ....................................................................................................................................................... 1-4

Ethernet ............................................................................................................................................. 1-4

Environmental ................................................................................................................................... 1-5

Compatibility............................................................................................................................................ 1-5

SECTION 2: Mounting and Wiring.......................................................................................................... 2-1

Determine the Signal Strength and Select a Location .......................................................................... 2-1

Mounting the IGSMHS............................................................................................................................ 2-2

Standard Mounting Procedure ......................................................................................................... 2-2

Wiring the IGSMHS .......................................................................................................................... 2-3

Wiring a Telco Line Fault Monitor for Zone Mode.......................................................................... 2-3

Wiring for ECP, 4204 and Two-4204 Modes.................................................................................... 2-4

Wiring for Zone Trigger Mode .......................................................................................................... 2-4

Wiring for Module Fault Relay......................................................................................................... 2-5

Ethernet Connections........................................................................................................................ 2-6

Power Connections and Options ............................................................................................................. 2-6

Powering the Communication Module ............................................................................................. 2-6

Backup Battery Connection .............................................................................................................. 2-7

Initial Power-Up Sequence ............................................................................................................... 2-7

SECTION 3: Programming the IGSMHS ............................................................................................... 3-1

General Information ................................................................................................................................ 3-1

Programming the Control Panel to work with the IGSMHS.......................................................... 3-1

Using the AlarmNet Direct Website ................................................................................................ 3-2

Using a 7720P Programming Tool.................................................................................................... 3-2

Using the Control Panel Programming Mode ................................................................................. 3-3

Programming Conventions ............................................................................................................... 3-3

ECP Mode Programming ......................................................................................................................... 3-3

ECP Status Codes.............................................................................................................................. 3-9

Alternative Modes (Zone Trigger, 4204 and Two-4204) ........................................................................ 3-9

Zone Trigger Mode............................................................................................................................. 3-9

Содержание AlarmNet IGSMHS

































































Результаты поиска

Содержание AlarmNet IGSMHS

Отзывы:

Honeywell AlarmNet IGSMHS, Инструкция по установке и настройке, Страница: 3 / 64

Результаты поиска

Содержание AlarmNet IGSMHS

Отзывы: