Honeywell AlarmNet IGSMHS Скачать руководство пользователя страница 43

Страница: 43 / 64

Section 4: Registration

4-3

Registration BAD
Pri&Sec – IDs BAD

Displayed when both primary and secondary subscriber IDs are
invalid.

Registration BAD
Pri ID – Need PIN

Displayed if this is a repair

replacement, or an error was made in

programming the Primary account information of IGSMHS for an

existing account. This prompt appears for 2 seconds. See the

Replacing an existing module

section below for further displays.

Registration BAD
2nd ID – Need PIN

This prompt is displayed if this is a repair

replacement, or an error

was made in programming the Secondary account information of
IGSMHS for an existing account. This prompt appears for 2

seconds. See the

Replacing an existing module

section below for

further displays.

Registration BAD
Pri&2nd – Need PIN

This prompt is displayed if this is a repair

replacement, or an error

was made in programming BOTH the Primary and Secondary

account information of

IGSMHS for an existing account. This prompt appears for 2
seconds. See the

Replacing an existing module

section below for

further displays.

Replacing an existing module using the programming tool

Enter PIN#

This prompt appears after pressing the [Shift} and down arrow

[



]

on the 7720P.

NOTE:

If it is necessary to exit registration mode, press ESC from

the 7720P programming tool.
Enter a 4-digit alphanumeric PIN number provided by your central

station, your dealer or an authorized AlarmNet representative.
Press the [Enter] key.

Registering …

The registration message is sent and the unit waits for

acknowledgement.

Registration
SUCCESS

If the PIN is valid, the new IGSMHS is registered and the old unit

unregistered. Additionally, AlarmNet sends a substitution alarm to
the central station.

Registration BAD

If you entered an invalid PIN, the appropriate message is displayed
depending on which account number is being replaced (see above for

exact wording). The registration process is repeated.

NOTE:

Each attempt causes a substitution alarm to be sent to the

central station.

Register by Phone

You can register the module by calling the AlarmNet Technical Assistance Center (TAC) at
1-800-222-6525. You will need the following information:



MAC number (found on the label).



Subscriber information (provided by the central station), including a city code, CSID, and
a subscriber ID.



When instructed to do so, triple-click the tamper switch to complete the registration.

Содержание AlarmNet IGSMHS

































































Результаты поиска

Содержание AlarmNet IGSMHS

Отзывы:

Honeywell AlarmNet IGSMHS, Инструкция по установке и настройке, Страница: 43 / 64

Результаты поиска

Содержание AlarmNet IGSMHS

Отзывы: