Honeywell AlarmNet IGSMHS Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 64

Honeywell AlarmNet IGSMHS Скачать руководство пользователя страница 27

Section 3: Programming the IGSMHS

3-9

PROMPTS

ENTRY

OPTIONS

DESCRIPTION

48

Review? Y/N

[Y] = review
[N] = exit

Reviewing Programming Mode Entries

To review the programming options (to ensure that
the correct entries have been made), press [Y]. The

programming prompts are displayed again. Use the

up/down arrow keys to scroll through the program
fields without changing any of the values. If a value

requires change, simply type in the correct value.

When the last field is displayed, the “REVIEW?”

prompt again appears.

To exit the programming mode

, press [N] in

response to the "REVIEW?" prompt, and refer to

Exiting Programming Mode

at the end of this section.

ECP Status Codes

When the IGSMHS is configured for ECP mode, it sends status messages to the control
panels for battery, power, tamper, and network connectivity failures. Some control panels

display these on the keypad as “LngRng Radio” followed by a 4-digit code (listed in the table

below). In addition, the Contact ID codes (listed in Appendix B) for these conditions are sent
to the central station by the module.

UL

The information in the following table is based on the VISTA-20 which has not been evaluated
with this communication module.

Table 3-3. Common ECP Keypad Display Status Codes

STATUS CODE

DESCRIPTION

0000

Control panel lost communication with IGSMHS.

0880

IGSMHS tamper detected (cover removed).

4005

IGSMHS has lost contact with AlarmNet.

000F

IGSMHS is not registered; account not activated.

0019 IGSMHS

shutdown.

0400

IGSMHS power on / reset AND the control panel lost communications with IGSMHS.

0C80

IGSMHS power on / reset AND tamper detected.

0C8F

IGSMHS power on / reset AND tamper detected AND not registered.

08E0

IGSMHS tamper detected and IGSMHS battery low.

3000

Primary power loss (will only be displayed in conjunction with another event).

8000

Battery charger failure (will only be displayed in conjunction with another event).

0060

Low battery (will only be displayed in conjunction with another event).

Alternative Modes (Zone Trigger, 4204 and Two-4204)

UL

The LYNX controls have not been evaluated with this communication module.

Zone Trigger Mode

There are six input zones available on the IGSMHS. Each zone is selectable for +V, -V, or

EOLR trigger. The first zone input can detect both pulsed and steady signals if connected to
a bell output. Additionally, the first zone input can be programmed to detect a single pulse

(characteristic of a Panic indication on the Lynx, LynxR or LynxR-EN control panel by

enabling the Lynx Panic option). If the programming option “Lynx Panic” is enabled, the
IGSMHS reports an alarm on zone 3. No restores are reported for this zone. If this option is

selected, the second physical zone input is ignored.

«
...
25
26
27
28
29
...
»

Содержание AlarmNet IGSMHS

































































Отзывы:

Нет отзывов