Honeywell AlarmNet IGSMHS Скачать руководство пользователя страница 32

Страница: 32 / 64

IGSMHS Installation and Setup Guide

3-14

PROMPTS

ZONE

TRIG.

4204/

2-4204

ENTRY

OPTIONS

DESCRIPTION

NOTE:

The next prompt only appears if the Comm Path Choice is IP&GSM, or IP.

IP Flt Time
(01 mins)_



[00-99]

In the event there is a loss of contact with the
network over the Ethernet connection, enter the

time delay (in minutes) before the IGSMHS

notifies the central station. IP failure will
always be sent to the central station as Primary

Communication Path Failure.

UL:

Must be one (01) minute.

NOTE:

The next prompt only appears if the Comm Path Choice is IP&GSM, or GSM.

GSM Flt Time
(01 mins)_



[00-99]

In the event the module detects a communica-
tion path failure, enter the time delay (in

minutes) before the IGSMHS notifies the
central station. A GSM failure will always be

sent to the central station as Secondary

Communication Path Failure.

UL:

Must be one (01) minute.

NOTE:

The next prompt only appears if the Comm Path Choice is IP&GSM.

Notify Panel Of_
(Both IP&GSM
Flts)_



[Both IP and

GSM Faults]
[Neither
fault]

If "Both IP and GSM Faults" is selected, the
device will only notify the control panel if both

communication paths fail, but will always send

notification of either failure to the central

station.

NOTE:

The fault relay output (if

programmed) will be triggered only if "Both IP

and GSM Faults" is selected.
Press the [space] key to scroll through choices.

UL:

Must be set to "Both IP and GSM Faults".

Flt Rel ON Y/N
(N)_



[Y], [N]

If enabled, the fault open collector output is
normally energized to ground, and de-energizes

(open circuit) in the event of a module fault.
For conditions that trip the fault relay refer to

Module Supervision Features

in Section 1.

Set to [Y] if fail-safe mode is desired.
See

Wiring for

Module Fault Relay

in Section 2.

UL:

Must be set to "Y".

Pwr Loss Rpt
Y/N (Y)_



[Y], [N]

Sends a primary power loss report to the central

station within 1-3 hours after its detection. A
restore report is sent within 1-3 hours after

power is restored.

UL Standard Installations

(using

transformer and battery)

Must be set to "Y".

Low Bat Rpt Y/N
(Y)_



[Y], [N]

Sends a low-battery report when a low battery
condition exists. A low-battery restore is

automatically sent when the low battery

condition clears.

UL Standard Installations

(using

transformer and battery)

Must be set to "Y".

Tamper Rpt Y/N
(Y)_



[Y], [N]

Sends a tamper report when the module detects

a tamper condition. A tamper restore is
automatically sent when the tamper condition

clears.

UL:

Must be set to "Y".

Содержание AlarmNet IGSMHS

































































Результаты поиска

Содержание AlarmNet IGSMHS

Отзывы:

Honeywell AlarmNet IGSMHS, Инструкция по установке и настройке, Страница: 32 / 64

Результаты поиска

Содержание AlarmNet IGSMHS

Отзывы: