Honeywell AlarmNet IGSMHS Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 64

Honeywell AlarmNet IGSMHS Скачать руководство пользователя страница 48

IGSMHS Installation and Setup Guide

5-4

Bat NLd: x.xxV
Bat Ld: x.xxV

Battery Voltage Display

The voltage levels of the battery connected to the
IGSMHS can be viewed on the 7720P. The first line of the display shows
the voltage level of the battery with no load. The second line of the
display shows loaded battery voltage. An asterisk (

*

) next to the voltage

indicates that this is below the accepted level.
Press the [Space] key to go to the next field.
Press the backspace [BS] key to go to the previous field.

Battery Charger
OK

Battery Charger Status Display

The status of the battery charger circuit of the
IGSMHS can be viewed on the 7720P. The status is either OK or NOT
OK.
Press the [Space] key to go to the next field.
Press the backspace [BS] key to go to the previous field.

Line Voltage
xx.xxV

Line Voltage Display

The line voltage of the IGSMHS can be viewed on the 7720P. An asterisk
(

*

) next to the voltage indicates that this is below the accepted level.

Press the [Space] key to go back to the System Status Display.
Press the backspace [BS] key to go to the previous field.

[T]

Test Msg Sent

Test Alarm

Sends a Test alarm to AlarmNet. Functional for a

registered

IGSMHS

only. If the device is not registered, a message is displayed indicating
that the command cannot be executed.

[X]

Reset CPU Y/N

Reset the IGSMHS.

Pressing [N] returns to diagnostic mode (blank screen = enter next
command or escape).
Pressing [Y] resets the module (blank screen = reset complete).

[



]

(UP
arrow)

Registering …

Registration

Registers a programmed IGSMHS with AlarmNet

.

[



]

(DN
arrow)

Enter PIN#

Registration with PIN for Replacement Module

Registers a replacement IGSMHS with AlarmNet, once programmed,
using the existing PIN #.

Force Upload of Configuration File to Server

Pressing [Y] will force the device to upload its entire configuration file to
the server.
Pressing [N] cancels the operation.

NOTE:

If the internet is not available, and the IGSMHS module is not

initialized when you enter this command, the following screen will be
displayed:

Cannot Upload
Try Later! _

[0]

Force Server Update?

Y/N

Wait for the RSSI LEDs to light, indicating the IGSMHS module has
completed its initialization, and try again.

[ENT
ER]

Strt Prog Mode?
Y/N_

Enter Program Mode

Press [Y] to enter program mode; otherwise, press [N].

«
...
46
47
48
49
50
...
»

Содержание AlarmNet IGSMHS

































































Отзывы:

Нет отзывов