Honeywell AlarmNet IGSMHS Скачать руководство пользователя страница 24

Страница: 24 / 64

IGSMHS Installation and Setup Guide

3-6

PROMPTS

ENTRY

OPTIONS

DESCRIPTION

Supervision
(UL Hi Line Sec)_



UL Hi Line
Sec



3 Minutes



6 Minutes

The AlarmNet network must hear at least one
supervisory message from the module during this

supervision period; otherwise, AlarmNet notifies the
central station that a communication failure has

occurred. (If the supervision period is changed after

registration, you must re-register the module.)
Press the [space] key to scroll through choices.

NOTE:

When “UL Hi Line Sec” is selected, a loss of

communications is treated as an alarm condition.

UL:

Must be set to "UL Hi Line Sec" (200 sec).

NOTE:

The next prompt only appears if the Comm Path Choice is IP&GSM.

GSM 24Hr Tst Y/N
(N)_

[Y], [N]

If enabled a message is sent every 24 hrs over GSM to
verify proper operation. If it fails, a Periodic Comm

Test Failure message will be sent over Ethernet.

UL:

Must be set to "Y".

Old Alarm Time
10 Minutes_



10 Minutes



15 Minutes



30 Minutes



1 Hour



2 Hours



4 Hours



8 Hours



12 Hours



24 Hours

Sets how long an undeliverable alarm is retried for
delivery to the central station. If the message is not

validated, it is retried until the old alarm time is

reached or the message is validated.
Press the [space] key to scroll through choices.

UL:

Must be 10 minutes.

NOTE:

The next prompt only appears if the Comm Path Choice is IP&GSM, or IP.

IP Flt Time
(01 mins)_

[00-99]

In the event there is a loss of contact with the network
over the Ethernet connection, enter the time delay (in

minutes) before the IGSMHS notifies the central

station. IP failure will always be sent to the central
station as Primary Communication Path Failure.

UL:

Must be one (01) minute.

NOTE:

The next prompt only appears if the Comm Path Choice is IP&GSM, or GSM.

GSM Flt Time
(01 mins)_

[00-99]

In the event the module detects a communication path
failure, enter the time delay (in minutes) before the

IGSMHS notifies the central station. A GSM failure

will always be sent to the central station as Secondary
Communication Path Failure.

UL:

Must be one (01) minute.

NOTE:

The next prompt only appears if the Comm Path Choice is IP&GSM.

Notify Panel Of_
(Both IP&GSM Flts)

[Both IP and

GSM Faults]
[Neither fault]

If "Both IP and GSM Faults" is selected, the device

will only notify the control panel if both
communication paths fail, but will always send

notification of either failure to the central station.

NOTE:

The fault relay output (if programmed) will be

triggered only if "Both IP and GSM Faults" is selected.

Press the [space] key to scroll through choices.

UL:

Must be set to "Both IP and GSM Faults".

Содержание AlarmNet IGSMHS

































































Результаты поиска

Содержание AlarmNet IGSMHS

Отзывы:

Honeywell AlarmNet IGSMHS, Инструкция по установке и настройке, Страница: 24 / 64

Результаты поиска

Содержание AlarmNet IGSMHS

Отзывы: