Honeywell AlarmNet IGSMHS Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 64

Honeywell AlarmNet IGSMHS Скачать руководство пользователя страница 46

IGSMHS Installation and Setup Guide

5-2

NOTE:

The Subnet Mask, Gateway IP Addr, DSN Serv IP and DHCP are only displayed if the Comm Path

Choice is “IP&GSM” or “IP”.

Subnet Mask
xxx.xxx.xxx.xxx

Displays the 32-bit address mask used to indicate the portion (bits) of the
IP address that is being used for the subnet address.
Press the [Space] key to go to the next field.
Press the backspace [BS] key to go to the previous field.

Gateway IP Addr
xxx.xxx.xxx.xxx

Displays the IP address assigned to the Gateway.
Press the [Space] key to go to the next field.
Press the backspace [BS] key to go to the previous field.

DNS Serv IP
xxx.xxx.xxx.xxx

Displays the IP address assigned to the DNS (Domain Name System)
server.
Press the [Space] key to go to the next field.
Press the backspace [BS] key to go to the previous field.

Encryption Test
AES Passed!

Performs a self-test of the AES encryption algorithm.
Press the [Space] key to go to the next field.
Press the backspace [BS] key to go to the previous field.

DHCP
OK

DHCP (Dynamic Host Configuration Protocol) indicates server is
performing satisfactorily.
Press the [Space] key to go to the Physical Link display.

GSM Status Displays

NOTE:

The Status Displays are available only if the Comm Path Choice is “IP&GSM” or “GSM”.

[E]

PriRSSI GPRS REG

-xxxdbm x x

GSM Status Display Screen 1

PriRSSI – Primary Site RSSI level in dBm.
GPRS – GPRS Service availability where “x” can be:
“Y” if GPRS is available
“N” if GPRS is Not available
REG – Registration status from radio module where
“x” can be:
N – Not Registered
H – Registered Home
S – Searching
D – Registration Denied
R – Registered Roaming
? – Unknown Registration State
Press the [Space] key to go to the next screen.
Press the backspace [BS] key to go to the last screen.

Cntry Netw LAC

xxx xxx xxxxx

GSM Status Display Screen 2

Cntry – Country Code
Netw – Network Code
LAC – Local area code
Press the [Space] key to get to the next screen.
Press the backspace [BS] key to go to the previous field.

Cell BaseSt Chan

xxxxx x xxx

GSM Status Display Screen 3

Cell – Base Station ID
BaseSt – Base Station Antenna Sector
Chan – Control Channel in use
Press the [Space] key to go to the next screen.
Press the backspace [BS] key to go to the previous field.

«
...
44
45
46
47
48
...
»

Содержание AlarmNet IGSMHS

































































Отзывы:

Нет отзывов