Honeywell AlarmNet IGSMHS Скачать руководство пользователя страница 31

Страница: 31 / 64

Section 3: Programming the IGSMHS

3-13

PROMPTS

ZONE

TRIG.

4204/

2-4204

ENTRY

OPTIONS

DESCRIPTION

Direct Wire Y/N
(N)_



[Y], [N]

Enables Direct Wire Downloading over IP. This
applies only to the Vista-32FB and VISTA BP

and FBP series control panels with revision 3.x.

BP and FBP panels rev 4.x and higher support
Downloading via IP over ECP. If [N], skip to

Prompt 17: "Supervision."

Keypad Address
(28)_



[01-30]

Must be programmed if using Direct Wire

downloading. Enter the appropriate device
address.

NOTES:

1. This address must also be programmed as an

alpha keypad in the control panel or an AUI

(Advanced User Interface) type device, if a full

enhanced graphic interface to the system is

desired and the control panel supports it. DO
NOT connect an actual keypad (or any other

device) assigned to this address.

2. This address must be unique from the "Device

Address" entered in Prompt 14, and cannot

equal that device address plus 1 (one) if using

2-4204 mode.

Supervision
(UL Hi Line Sec)_





UL Hi
Line Sec



3 Min-

utes



6 Min-
utes

The AlarmNet network must hear at least one
supervisory message from the module during

this supervision period; otherwise, AlarmNet

notifies the central station that a communica-
tion failure has occurred. (If the supervision

period is changed after registration, you must

re-register the module.)
Press the [space] key to scroll through choices.

NOTE:

When “UL Hi Line Sec” is selected, a

loss of communications is treated as an alarm

condition.

UL:

Must be set to "UL Hi Line Sec" (200 sec).

NOTE:

The next prompt only appears if the Comm Path Choice is IP&GSM.

GSM 24Hr Tst
Y/N
(N)_



[Y], [N]

If enabled a message is sent every 24 hrs over

GSM to verify proper operation. If it fails, a
Periodic Comm Test Failure message will be

sent over Ethernet.

UL:

Must be set to "Y".

Old Alarm Time
10 Minutes_





10 Min



15 Min



30 Min



1 Hr



2 Hrs



4 Hrs



8 Hrs



12 Hrs



24 Hrs

Sets how long an undeliverable alarm is retried
for delivery to the central station. If the

message is not validated, it is retried until the
old alarm time is reached or the message is

validated.

Press the [space] key to scroll through choices.

UL:

Must be set to 10 minutes.

Содержание AlarmNet IGSMHS

































































Результаты поиска

Содержание AlarmNet IGSMHS

Отзывы:

Honeywell AlarmNet IGSMHS, Инструкция по установке и настройке, Страница: 31 / 64

Результаты поиска

Содержание AlarmNet IGSMHS

Отзывы: