Honeywell AlarmNet IGSMHS Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 64

Honeywell AlarmNet IGSMHS Скачать руководство пользователя страница 16

IGSMHS Installation and Setup Guide

2-6

Ethernet Connections

UL



For UL installations, the Cat. 5 Ethernet connection between the IGSMHS and the router
cannot exceed 12 feet with both the IGSMHS and the router located within the same room.



Use a Listed cable

/

DSL router suited for the application.

Connect one end of the Ethernet cable (Category 5) to the IGSMHS’s RJ45 Ethernet
connector and the other end to the cable

/

DSL router as shown in the figure below.

TO ROUTER

RJ45
(FOR INTERNET
CONNECTION)

7720P

PROGRAM

CONNECTOR

J1

BATTERY

CONNECTOR

RSSI

M0

M1

GPRS

IBS

iGSMBR-012-V0

Figure 2-7. Ethernet Connections

Power Connections and Options

Powering the Communication Module

For a standard installation, primary power is provided by the AC plug-in transformer. For

ECP communication, you must also connect the +12VDC AUX voltage output of the control
panel (9.6V-13.8V typical) (see Figure 2-8).
In all installations, TB1-4 GND must be connected to ground (GND) on the control panel.

iGSMBR-013-V0

12V AUX

GND

COMMUNICATIONS
MODULE

CONTROL PANEL

GND

ECP (+) VOLTAGE INPUT

2

1

4

3

TB1

TRANSFORMER

AC INPUT 2

AC INPUT 1

J1

BATTERY

Figure 2-8. Powering the Communications Module

NOTE:

When calculating the total load on the auxiliary power output of the control panel, budget 10mA

for the IGSMHS when using ECP mode.

Standard

Installation

«
...
14
15
16
17
18
...
»

Содержание AlarmNet IGSMHS

































































Отзывы:

Нет отзывов