Honeywell AlarmNet IGSMHS Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 64

Honeywell AlarmNet IGSMHS Скачать руководство пользователя страница 20

IGSMHS Installation and Setup Guide

3-2

Using the AlarmNet Direct Website

To program the module via the website (if you are already signed up for this service), go to:

https://services.alarmnet.com/AlarmNetDirect/userlogin.aspx

If you are not signed up for this service, click on “Dealer Sign-Up.
Log in and follow the on-screen prompts.
Please have the following information available when programming the module:
1.

Primary City ID (two-digit number)

2.

Primary Central Station ID (two-digit hexadecimal number)

3.

Primary Subscriber ID (four-digit number)

4.

MAC ID and MAC CRC number (located on the outside of box and on label inside module)

of the communication module you are installing

After programming is complete, you must transfer the data to the module and the module
must be registered. Refer to

Section 4: Registration

, for further instructions.

Using a 7720P Programming Tool

Connect the 7720P Programming Tool as shown below. The IGSMHS powers the 7720P

Programming Tool via the programming jack, and automatically senses the presence of the
7720P when it is plugged in.

7720P
PROGRAM
CONNECTOR

A

B

C

D

E

F

S

T

X

1

2

3

4

5

6

9

8

7

#

0

Xmit

Shift

Space

Enter

Shift

N / Y

BS / ESC

/

7720 PROGRAMMING TOOL

RSSI

M0

M1

GPRS

IBS

iGSMBR-015-V0

Figure 3-1. Cable Connections

Each key of the 7720P has two possible functions: a normal function and a Shift function.
To perform a normal key function, simply press the desired key.
To perform a Shift function, press the [shift] key, and then press the appropriate key.
The prompts in this document reflect use of the 7720P Programming Tool. The table below

lists each normal and shift key function.

Table 3-1. 7720P Normal and Shift Key (shift LED lit) Functions

KEY

NORMAL KEY FUNCTION

SHIFT KEY FUNCTION

BS

/

ESC

[BS]: Press to delete entry

[ESC]: Press to quit program mode; also can reset
programming defaults*



/



[



]: Scroll down programming

[



]: Scroll up programming

N

/

Y

[N]: Press for "NO" answer

[Y]: Press SHIFT-Y for "YES" answer

SHIFT

Press before pressing a SHIFT key function. Will light SHIFT LED. LED goes out once a key
is pressed. Press again for each SHIFT function desired.

1

/

A

[1]: For entering the number 1

[A]: For entering letter A

2

/

B

[2]: For entering the number 2

[B]: For entering letter B

3

/

C

[3]: For entering the number 3

[C]: For entering letter C

4

/

D

[4]: For entering the number 4

[D]: For entering letter D

5

/

E

[5]: For entering the number 5

[E]: For entering letter E

«
...
18
19
20
21
22
...
»

Содержание AlarmNet IGSMHS

































































Отзывы:

Нет отзывов